JRC JHS-180 - Page 56

5-30
(2) Check and Set the Channel Management
The inputted Channel Management detail has to be registered to the transponder for channel
management operation.
Pressing the “[Check]” select key checks whether or not the inputted detail can be set to the
transponder, and display “OK” or “NG” as the result.
When the check result was “OK”, then select key function “[Set]” is appears on the “[List] ”
position.
(Checked Channel Management detail : “OK”)
ＣＨ ＭＡＮＡＧＥＭＥＮＴ ＵＴＣ１１：４３
２．ＣＨ Ｂ：２０８８ ＮＡＲＲＯＷ ＲＸ
３．ＴＸ ＰＯＷＥＲ ：ＨＩＧＨ
６．ＡＲＥＡ Ｎ ３５°３３．３８７０‘
４．ＺＯＮＥ ＳＩＺＥ：５ｎｍ
（ＳＷ） Ｅ１３９°５４．５７８０‘ ＳＥＴ＞
１．ＣＨ Ａ：２０８７ ＷＩＤＥ ＴＸ／ＲＸ
５．ＡＲＥＡ Ｎ ３５°３３．３８７０‘ＣＨＥＣＫ＞
（ＮＥ） Ｅ１３９°５４．５７８０‘ＯＫ
○
○
○
○
ＢＲＧ ： ＲＡＮＧＥ ＮＡＭＥ／ＭＭＳＩ
２７０°： ０．１８ＮＭ ＪＲＣ ＭＡＲＵ１
３５°： ０．２９ＮＭ ＪＲＣ ＭＡＲＵ２
２２°： ０．９２ＮＭ ＪＲＣ ＭＡＲＵ１
(Checked Channel Management detail : “NG”)
ＣＨ ＭＡＮＡＧＥＭＥＮＴ ＵＴＣ１１：４３
２．ＣＨ Ｂ：２０８８ ＮＡＲＲＯＷ ＲＸ
３．ＴＸ ＰＯＷＥＲ ：ＨＩＧＨ
６．ＡＲＥＡ Ｎ ３５°３３．３８７０‘
４．ＺＯＮＥ ＳＩＺＥ：５ｎｍ
（ＳＷ） Ｅ１３９°５４．５７８０‘ ＳＥＴ＞
１．ＣＨ Ａ：２０８７ ＷＩＤＥ ＴＸ／ＲＸ
５．ＡＲＥＡ Ｎ ３５°３３．３８７０‘ＣＨＥＣＫ＞
（ＮＥ） Ｅ１３９°５４．５７８０‘ＮＧ
ＮＧ：ＡＲＥＡ ＣＯＮＲＮＥＲ ＥＲ ＮＧ
○
○
○
○
ＢＲＧ ： ＲＡＮＧＥ ＮＡＭＥ／ＭＭＳＩ
２７０°： ０．１８ＮＭ ＪＲＣ ＭＡＲＵ１
３５°： ０．２９ＮＭ ＪＲＣ ＭＡＲＵ２
２２°： ０．９２ＮＭ ＪＲＣ ＭＡＲＵ１
Pressing this select key checks whether o
r
not the inputted detail can be registered to the
transponder.
Pressing this select key registers the inputted
channel management detail to the transponder.
Pressing this select key checks whether o
r
not the inputted detail can be registered to the
transponder.
Pressing this select key registers the inputted
channel management detail to the transponder.
Reason about check result “NG”
Check result “OK”