JRC JLN-205MK2 User Manual (English)

Questions and Answers:

M
Melissa CarrollAug 17, 2025
What to do if the JRC Marine Equipment power does not turn on?
- I
  iramirezAug 17, 2025
  If your JRC Marine Equipment isn't powering on, several issues could be at fault. First, make sure the ship junction box is supplying power and that the cabling is correctly connected. If you're using optional power supply equipment (only MID), verify its cabling as well. Also, inspect the fuse connected to the power cable and the fuse in the optional power supply equipment (only MID); replace them if necessary, assuming the cabling is normal. For LOG models, check the connection. If none of these steps resolve the issue, the display unit switch may be broken.
D
Daniel BarnesAug 19, 2025
Why is there no transmission to external devices from my JRC JLN-205MK2?
- M
  mcoxAug 19, 2025
  If your JRC Marine Equipment isn't transmitting to external devices, start by checking the interface settings to ensure the output settings are configured correctly and that the channel is correct. If the problem persists, the DISP-DPU or POWER SUPPLY UNIT may be broken.
K
Kenneth WhiteAug 22, 2025
What should I do if my JRC JLN-205MK2 is not receiving data from the sensor?
- C
  Cynthia MathewsAug 22, 2025
  If your JRC Marine Equipment isn't receiving data from the sensor, check the connection cable to ensure it is properly connected. If the connection is secure, the sensor itself may be broken.
S
Sarah AlvaradoAug 25, 2025
Why is data not being shared on my JRC JLN-205MK2 Marine Equipment?
- M
  Meredith PorterAug 26, 2025
  If data is not being shared on your JRC Marine Equipment, verify that the RS-485 bit rate is correct. Also, check that the RS-485 output sentence is selected, and confirm that the cable is properly connected.
C
charles62Aug 28, 2025
Why are the dimmers not interlocked on my JRC JLN-205MK2 Marine Equipment?
- R
  Renee SmithAug 28, 2025
  If the dimmers are not interlocked on your JRC Marine Equipment, check the RS-485 bit rate, ensure the dimmer group number is correct, and verify the dimmer unit. Also, make sure the cable is properly connected.
A
Amy WestAug 30, 2025
What to do if the alarm sound is not generated on JRC Marine Equipment?
- A
  Allen MooreAug 30, 2025
  If the alarm sound is not generated on your JRC Marine Equipment, check the alarm sound setting to ensure it is not turned off. If the setting is correct, the buzzer may be broken.
T
Terrance VelasquezSep 2, 2025
What to do if JRC Marine Equipment power does not turn on?
- M
  Michael LiuSep 2, 2025
  If your JRC Marine Equipment isn't powering on, first ensure the ship junction box is supplying power by checking the cabling. Also, if applicable, verify the power supply unit cabling is correctly connected (only MID models). If the cabling is fine, inspect and replace the fuse connected to the power cable or the power supply equipment fuse (only MID models) if blown. For LOG models, check the connection. If problems persist, the display unit switch may be broken, and you should consult with JRC or their agents.
A
Austin EdwardsSep 4, 2025
How to fix JRC JLN-205MK2 when the dimmers are not interlocked?
- T
  Thomas MurphySep 4, 2025
  If the dimmer on your JRC Marine Equipment isn't interlocked, verify that the RS-485 or Daisy-chain bit rate is correct (Daisy-chain is only for MID models), check that the dimmer group number is correct, and ensure the dimmer unit is correct. Also, check the RS-485 or Daisy-chain connection for any disconnections (Daisy-chain is only for MID models).
B
Brandon CobbSep 7, 2025
What to do if JRC JLN-205MK2 has no reception from the sensor?
- B
  bmurphySep 7, 2025
  If your JRC Marine Equipment isn't receiving signals from the sensor, first check the connection cable to ensure it is properly connected. If the connection is secure, the sensor itself may be broken, and you should consult with JRC or their agents.