13
LCD Door
1[LCD BRIGHT +/–] LCD brightness +/– button
This button is for adjusting the brightness of the LCD mon-
itor display.
• Pushing the button in the + direction makes the monitor
brighter.
• Pushing the button in the – direction makes the monitor
darker.
• Pushing the +/– buttons simultaneously returns the set-
ting to the standard setting.
2[CH-1/CH-2 AUDIO SELECT] CH-1/CH-2 audio selector
switch
Selects the method of adjusting the CH-1 and CH-2 audio
channel audio levels.
3[TC DISPLAY] TC/UB display switch
Selects the contents displayed on the TC counter of the
LCD monitor or in the viewfinder. (This switch works when
the TC/UB item on the LCD/VF[3/4] menu screen is set to
ON.)
4[TC GENE.] Time code generator setting switch
Switch for setting the time code generator to preset mode
or regeneration mode. It is also used to select the time
code run mode when the preset mode is selected.
MEMO
Preset of time code and user’s bits is performed on the TC/
UB/CLOCK menu.
X Seepage44.
X See “TC/UB/CLOCK Menu Screen” on page 90.
When performing 1080i recording with DR-HD100 (HDD
unit by FOCUS enhancement) connected, configure the
setting as follows.
• When the DR-HD100 is set to TC EXT set the TC GENE.
switch on the camcorder to FREE.
• When the DR-HD100 is set to TC REC RUN, TC FREE
RUN or TC REGEN the camcorder Time Code is not
recorded in the DR-HD100.
5[CAM/VTR] Camera/VTR mode switch button
Each time you press this button, the mode switches
between camera mode and VTR mode.
When you do this, the VTR indicator f on page 19 dis-
plays the following statuses.
While the mode is being switched : Flashing
In VTR mode : Lit
In camera mode : Off
• Select the Camera mode to record the camera image.
• Select the VTR mode to playback VTR or to input the
HDV/DV signal from the IEEE1394 connector 0 on
page 16. (HDV/DV signal input is possible with the
GYHD200U/GY-HD201E.)
• When the power is turned on, the mode becomes the
Camera mode.
AUTO : The audio level is automatically adjusted
according to the input level. When excessive
audio is input, the limiter works to suppress
the audio level.
The “AUTO” LED in the CH-1/CH-2 AUDIO
LEVEL area f on page 15 lights.
MANU : Allows you to adjust the audio levels using
the CH-1/CH-2 AUDIO LEVEL volume con-
trols f on page 15.
Set AUDIO LIMITER on the AUDIO/MIC[1/2]
menu screen to use limiter functions when
excessive audio is input.
X See “AUDIO LIMITER” on page 84.
TC : Set to this position to display time code values.
UB : Set to this position to display the user’s bits values.
CH-2
CH-1
-
+
AUDIO SELECT
MANU
AUTO
TC
LCD BRIGHT
DISPLAY
TC
UB
FREE
REGEN
GENE.
REC
CAM/VTR
5
1
2
3
4
FREE : The preset mode is selected, and the time
code run mode becomes the FREE run
mode.
Set to this position to record with the time
code or user’s bits set anew (preset). In this
setting, the time code always operates in the
run mode.
* If this setting is used when recording
scenes one after another, the time codes
become discontinuous at the transition
points between scenes.
REC : The preset mode is selected, and the time
code run mode becomes the REC run mode.
Set to this position to record with the time
code or user’s bits set anew (preset). The
time code operates in the run mode during
recording only. If this setting is used when
recording scenes one after another, the time
codes are recorded as continuous time
codes.
REGEN : Regeneration mode, in which this device
reads existing time codes on the tape and
records time codes in continuation of the
existing ones. Set to this position when you
want to add additional time codes to time
codes already recorded on the tape.
e_hd200.book Page 13 Friday, February 1, 2008 4:04 PM
To Next Page
Loading...
