JVC GY-HM150U - Audio Recording; Setting the Reference Audio Recording Level; Using the Built-In Microphone; Using an External Microphone Connected to the [INPUT1;INPUT2] Terminal

38
Shooting
Applicable to: Camera mode
There are two ways to input audio sound.
A Built-in microphone
B [INPUT1] terminal / [INPUT2] terminal
● The priority order of the input is in the sequence of B > A .
● To use the built-in microphone, remove the audio unit cable
from the [AUDIO IN] terminal.
Setting the Reference Audio Recording
Level
Applicable to: Full Auto shooting mode A, Manual shooting
mode M
 Set using [Record Set] menu B[Audio
Set]B[Audio Ref. Level]. (A-20dBB/A-12dBB)
(A Page 65)
Using the Built-in Microphone
Applicable to: Full Auto shooting mode A, Manual shooting
mode M
 Setting the input level.
Set using [Record Set] menu B[Audio Set]B[Internal Mic
Level]. (A Page 65)
Using an External Microphone Connected to
the [INPUT1/INPUT2] Terminal
Applicable to: Full Auto shooting mode A, Manual shooting
mode M
Preparation: Connect a microphone to the [INPUT1/INPUT2]
terminal.
(A Page 15)
 Selecting [CH-2] audio
Configure the [CH-2 INPUT] switch.
●
[INPUT1]: Inputs the audio from the [INPUT1] terminal to
[CH-2].
● [INPUT2]: Inputs the audio from the [INPUT2] terminal to
[CH-2].
Memo :
● The audio from the [INPUT1] terminal is input to [CH-1]
regardless of the setting.
 Selecting the audio input to the [INPUT1] or
[INPUT2] terminal
Configure the [AUDIO INPUT 1/2] switch.
Caution :
● When connecting a device that does not require a +48 V
power supply, make sure that it is not set to the [MIC+48V]
position.
 Adjusting the audio recording level
Select a method for adjusting the audio recording level.
● Configure the [CH1/CH2 AUDIO SELECT] switch.
● Select whether to set each channel to the [AUTO] or
[MANUAL] mode.
Reducing Wind Noise
Wind noise for each microphone can be reduced.
 Menu setting
Set [Record Set] menu B[Audio Set]B[Input1 Mic Wind
Cut]/[Input2 Mic Wind Cut]/[Internal Mic Wind Cut] to
AOnB. (A Page 65)
Audio Recording
Terminal Audio Input
[INPUT1] Input to [CH1(L)] at all times. Input to [CH2(R)] can be
enabled using the [CH-2 INPUT] switch.
[INPUT2]
Input to [CH2(R)] can be enabled using the [CH-2
INPUT] switch.
R
E
M
O
T
E
A Built-in Microphone
B[INPUT1/INPUT2] Terminals
Audio Unit Cable
[LINE] Use this setting when connecting to an audio
device or other equipment.
[MIC] Use this setting when connecting to a
dynamic microphone.
[MIC+48V] Use this setting when connecting to a
microphone that requires a +48 V power
supply (phantom microphone), or when using
the supplied microphone.
[AUTO] : Use this setting to enable the auto
adjustment mode.
[MANUAL] : Use this setting to enable the manual
adjustment mode. Adjust the audio
recording level using the [CH1/CH2 AUDIO
LEVEL] knob.
CH-2 INPUT
CH-1
3
4
5
2
1
2
3
0
CH-2
AUDIO IN PUT
AUTO MANUAL
AUTO MANUAL
AUDIO
SELECT
INPUT1
INPUT2
- LINE -
- MIC -
MIC+48V
INPUT1
INPUT2
[CH1/CH2 AUDIO SELECT] Switch
[AUDIO INPUT 1/2] Switch
[CH-2 INPUT]
Switch
[CH1/CH2 AUDIO LEVEL] Knob
GY-HM150U.book Page 38 Monday, September 5, 2011 1:48 AM