AGC Mode
For setting whether to link the limiter operation of
[CH1] and [CH2].
Select “Link” to link or “Separate
” to separate.
[Setting Values: Link, RSeparate]
Memo :
0
Enabled only
when both the [AUX] input terminal
and [INPUT1/INPUT2] input terminal are set to
“LINE” or “MIC”, and CH1/CH2 of the [CH1/CH2
AUTO/MANUAL] switch is set to “AUTO”.
XLR Manual Level
For setting whether to link manual audio
adjustment operation between
[INPUT1] and
[INPUT2] terminals.
Select “Link
” to link or “Separate” to separate.
When this item is set to “Link”, adjust the recording
level using the [CH1] recording level adjustment
knob.
[Setting Values: Link, RSeparate]
Memo :
0
Enabled only when both the [INPUT1/INPUT2
]
input terminals are set to “LINE” or “MIC”, and
both [CH1]/[CH2] of the [CH1/CH2 AUTO/
MANUAL] selection switches are set to
“MANUAL”.
0
When this item is set to
“Link”, [CH2] recording
level adjustment knob is disabled.
Int. Mic Separation
For setting the enhancement level of the stereo
effect of the built-in microphone.
0
1 to 4:
Enhances
the
stereo effect. Increasing the value
increases the stereo effect.
0
Effect off:
Does not enhance the stereo effect.
0
Mono:
Sets the built-in microphone to monaural.
[Setting Values: 1 to 4, Effect off, Mono (R2)]
Memo :
0
When any value from 1 to 4 is selected, the
sound quality changes slightly due to the
process of enhancing the stereo effect. This is
normal.
0
This menu is enabled when the [CH1]/[CH2]
selection switch is set to “INT
”.
Test Tone
For specifying whether to output the audio test
signals (1 kHz) during color bar output.
[Setting Values: On, ROff]
INPUT1/2 Wind Cut
For selecting
whether to cut the low frequencies of
the audio input signals (low-cut) when the [INPUT1/
INPUT2] switch is set to “MIC” or “MIC+48V”.
Set this item to reduce wind noise from the
microphone.
0
Both:
Enables low-cut on both the [INPUT1] and
[
INPUT2
] terminals.
0
INPUT2:
Enables low-cut on the audio of the [INPUT2
]
terminal only.
0
INPUT1:
Enables low-cut on the audio of the [INPUT1]
terminal only.
0
Off:
Disables low-cut.
[Setting Values: Both, INPUT2, INPUT1, ROff]
Int. Mic Wind Cut
For selecting
whether to cut the low frequencies of
the audio input signals (low-cut) from the built-in
microphone. Set this item to “On” to reduce wind
noise from the microphone.
[Setting Values: On, ROff]
Equalizer
You can
correct the characteristic and enhance the
sound of the connected microphone using this
equalizer setting.
For setting the audio frequency from a 5-band
equalizer.
0
Frequency:
100Hz, 330Hz, 1kHz, 3.3kHz, 10kHz
0
Variable level:
± 6dB (1dB step)
Memo :
0
Audio will be recorded in the characteristic set
in the equalizer.
0
Set all bands to “0dB” to bypass the equalizer.
0
When the
equalizer level is set to the + side, the
audio may be distorted. In this case, reduce the
recording level in Manual mode.
0
If the values of multiple frequencies are
changed, the specified levels and the actual
levels may be different due to interference
between the frequency bands.
0
This function is enabled only when both
[INPUT1/2 Wind Cut] and [Int. Mic Wind Cut] are
set to “Off”.
114
Menu Display and Detailed Settings
To Next Page
Loading...
