JVC GY-HM890U - Page 109

AE Level
For setting the convergence level during AE (Auto
Exposure).
This can also be adjusted using the cross-shaped
button (HI) on the right side.
[Setting Values: -6 to +6 (R0)]
Memo :
0
In all the following cases, “---” is displayed and
selection cannot be made.
0
When gain is set to a value other than “ALC”
0
When [Shutter] is set to a value other than
“EEI”
0
When the [IRIS A/M] selection switch is set to
“M” (only when the supplied lens is used)
AE Speed
For setting the convergence speed during AE (Auto
Exposure).
[Setting Values: RFast, Middle, Slow]
ALC Limit
For setting the maximum gain value of “ALC”,
which electrically boosts the sensitivity level
according to the brightness automatically.
[Setting Values: 24dB, R18dB, 12dB, 6dB]
Auto Iris Limit (OPEN)
For setting the limit value of the OPEN end when
auto iris is enabled.
[Setting Values: F5.6, F4, F2.8, F2, F1.6, RF1.4]
Auto Iris Limit (CLOSE)
For setting the limit value of the CLOSE end when
auto iris is enabled.
[Setting Values: RF16, F11, F8, F5.6]
EEI Limit
For setting the shutter speed control range when
the Automatic Shutter mode (EEI) is enabled.
[Setting Values: 4F-stop, R3F-stop, 2F-stop]
Smooth Trans
For setting the shock reduction function, which
slows down the sudden change when switching
with the [GAIN L/M/H] selection switch or
[WHT.BAL B/A/PRESET] switch.
[Setting Values: Fast, Middle, Slow, ROff]
Memo :
0
This feature does not function when the [FULL
AUTO] switch is “ON”, while the [GAIN L/M/H]
selection switch or [WHT.BAL B/A/PRESET]
switch is disabled.
FAW
For setting where to assign the FAW (Full Auto
White Balance) feature in the [WHT.BAL B/A/
PRESET] switch.
[Setting Values: B, A, PRESET, RNone]
Memo :
0
When the [FULL AUTO] switch on the camera
recorder is set to “ON”, and [FULL AUTO] B
[White Balance] is set to “FAW”, the setting is
fixed at “FAW”.
GAIN L/GAIN M/GAIN H
For setting the gain value of each position on the
[GAIN L/M/H] selection switch.
When “ALC” is selected, the camera recorder
switches to the Auto Gain mode.
[Setting Values: ALC, 24dB, 21dB, 18dB, 15dB,
12dB, 9dB, 6dB, 3dB, 0dB, -3dB, -6dB]
(Default values GAIN L: 0dB, GAIN M: 6dB, GAIN
H: 12dB)
Memo :
0
When the [FULL AUTO] switch on the camera
recorder is set to “ON”, and [FULL AUTO] B
[Gain] is set to “ALC”, the setting is fixed at
“ALC”.
AE LEVEL SW
For specifying the operation of the cross-shaped
button (HI) on the right side.
0
AE LEVEL/VFR:
Sets the number of frames during Variable
Frame Rec, and operates as the AE level setting
button in other cases.
(A P93 [Variable Frame Rec] )
0
AE Level:
Operates as the AE level setting button at all
times.
0
Disable:
Disables the button.
[Setting Values: AE LEVEL/VFR, RAE Level,
Disable]
Camera Function Menu
109
Menu Display and Detailed Settings