Memo :
0
You can specify whether to display the time
code, user’s bit, or turn off the display in
[LCD/VF] B [Display Settings] B [TC/UB].
This item will not be displayed when “Off” is
selected.
(A P123 [ TC/UB ] )
Z
Time Code Lock Indicator
When the built-in time code generator is
synchronized to the external time code data
input during the synchronization of time code
with another camera recorder, Z lights up.
(A P78 [Synchronizing the Time Code with an
External Time Code Generator] )
a
Live streaming mark
When [Main Menu] B [System] B [Network]/
[Settings] B [Live Streaming Set] B [Live
Streaming] is set to “On”, the distribution status
is displayed.
(A P138 [ Live Streaming ] )
Icon Status
.
(Red)
0
Distribution in progress
(good connection quality)
0
Blinks when distribution
starts or stops
.
(Red)
Distribution in progress (poor
connection quality)
.
(Yellow)
Waiting for connection (during
RTSP/RTP) or connection failed
b
Event/Warning Display Area
Displays error messages.
(A P202 [Error Messages and Actions] )
c
Media Status
---- : A card is not detected in the
selected slot, and [Tally
System] is also not set to
“Studio”
(A P130 [ Tally System ] )
STBY : Recording standby
RREC : Recording
REVIEW : Clip Review
(A P83 [Viewing Recorded Videos Immediately
(Clip Review)] )
STBY P : Pre Rec recording standby
(A P89 [Pre Rec] )
RRECP : Pre Rec recording
(A P89 [Pre Rec] )
STBY C : Clip Continuous Rec recording
standby
(A P89 [Clip Continuous Rec] )
RRECC : Clip Continuous Rec recording
(A P89 [Clip Continuous Rec] )
STBYC
(displayed in
yellow)
: Clip Continuous Rec recording
pause
(A P89 [Clip Continuous Rec] )
STBY N : Interval Rec recording standby
(A P92 [Interval Rec] )
STBYN
(displayed in
red)
: Interval recording pause
RRECN : Interval Rec recording
(A P92 [Interval Rec] )
STBY M : Frame Rec recording standby
(A P91 [Frame Rec] )
RRECM : Frame Rec recording
(A P91 [Frame Rec] )
STBYM
(displayed in
yellow)
: Frame Rec recording pause
(A P91 [Frame Rec] )
STOP : Unable to record to the card in
the slot
P.OFF : Power OFF
Q
: During clip cutter recording
(displayed for 3 seconds)
(A P85 [Splitting the Clips Freely (Clip Cutter
Trig)] )
CALL : Receiving call signals from an
external device, such as a
remote control unit
PGM : Receiving program signals
from an external device, such
as a remote control unit
PVW : Receiving preview signals
from an external device, such
as a remote control unit
d
Dual Rec/Backup Rec Display
“DUAL” is displayed in the Dual Rec mode and
“BACKUP” is displayed in the Backup Rec
mode.
(A P136 [ Slot Mode ] )
Memo :
0
This item is not displayed when [Slot Mode] is
set to “Series”.
0
This item is not displayed when [Main Menu] B
[LCD/VF] B [Display Settings] B [Media
Remain] is set to “Off”. However, warnings will
be displayed.
(A P123 [ Media Remain ] )
e
OK Mark
Displayed when OK mark has been appended.
(A P99 [Appending/Deleting OK Mark] )
150
Display Screen in Camera Mode
Display/Status Screen
To Next Page
Loading...
