JVC PD-35B50BJ - Page 41

(No.YA098) 1-37
4.5 INITIAL SETTING VALUES IN THE SERVICE MENU SETTING MODE
• Perform fine-tuning based on the “initial setting values” using the remote control when in the SERVICE MENU setting mode.
• The “initial setting values” serve only as an indication rough standard and therefore the values with which optimal display can be
achieved may be different from the initial setting values. But, don't change the values that are not written in “ADJUSTMENT
PROCEDURE”. They are fixed values.
Item No. Item
Variable range
Setting value
PAL SECAM NTSC
S001 PREPARE 0~31 0 0 0
S002 NTSC BL 0~15 1 1 1
S003 NTSC CNT 0~255 44 44 44
S004 NT CR OF 0~15 4 4 4
S005 NT CB OF 0~15 4 4 4
S006 525i BL 0~15 1 1 1
S007 525i CNT 0~255 44 44 44
S008 5i CB OF 0~15 0 0 0
S009 5i CR OF 0~15 0 0 0
S010 5i CR GN 0~15 4 4 4
S011 5i CB GN 0~15 4 4 4
S012 HD BL 0~63 0 0 0
S013 HD CB OF 0~63 0 0 0
S014 HD CR OF 0~63 0 0 0
S015 RT CONT 0~15 7 7 7
S016 RT CB OF 0~15 2 2 2
S017 RT CR OF 0~15 5 5 5
S018 RT CL GA 0~15 4 4 4
S019 PC CL MB 0~7 0 0 0
S020 PC CL LB 0~31 0 0 0
S021 PC CL MR 0~7 0 0 0
S022 PC CL LR 0~31 0 0 0
S023 (NO DISPLAY) 0~255 0 0 0
S024 (NO DISPLAY) 0~255 0 0 0
S025 (NO DISPLAY) 0~255 0 0 0
S026 (NO DISPLAY) 0~255 0 0 0
S027 (NO DISPLAY) 0~255 0 0 0
S028 (NO DISPLAY) 0~255 0 0 0
S029 (NO DISPLAY) 0~255 0 0 0
S030 R DRIVE 0~255 0 0 0
S031 G DRIVE 0~255 0 0 0
S032 B DRIVE 0~255 0 0 0
S033 (NO DISPLAY) 0~255 0 0 0
S034 (NO DISPLAY) 0~255 0 0 0
S035 (NO DISPLAY) 0~255 0 0 0
S036 (NO DISPLAY) 0~255 0 0 0
S037 (NO DISPLAY) 0~255 0 0 0
S038 (NO DISPLAY) 0~255 0 0 0
S039 (NO DISPLAY) 0~255 0 0 0
Item No. Item Variable range
Setting value
PAL SECAM NTSC
T001 IN LEVEL 0~255 0 0 0
T002 LOW SEP 0~255 0 0 0
T003 HIGH SEP 0~255 0 0 0
T004 AFC 0~255 0 0 0
T005 (NO DISPLAY) 0~255 0 0 0
T006 ATT V ON 0~1 0 0 0
T007 ATT U ON 0~1 0 0 0
T008 ATT C ON 0~1 0 0 0
T009 (NO DISPLAY) 0~255 0 0 0
T010 (NO DISPLAY) 0~255 0 0 0
4.5.1 [1.ADJUST]
4.5.1.1 VIDEO SYSTEM
4.5.1.2 AUDIO SYSTEM