JVL Industri Elektronik A/S - User Manual - Ethernet for MAC and MIS motors 25
2.3 Connector description
(MAC00-Ex41 continued)
“I/O” - I/O’s and interface. M12 - 17pin female connector.
Signal name Description Pin no.
JVL Cable
WI1009M12
M17TxxN
Isolation
group
(see note)
IN1 Input channel 1. Can be used as digital input 1 Brown 2
GND
Ground intended to be used toghether with the
other signals related to isolation group 1 in this
connector
2 Blue 1
IN2 Input channel 2. Can be used as digital input 3 White 2
IN3 Input channel 3. Can be used as digital input 4 Green 2
B2- ** RS422/RS485 Multifunction I/O terminal B2- 5 Pink 1
IN4 Input channel 4. Can be used as digital input 6 Yellow 2
A2- ** RS422/RS485 Multifunction I/O terminal A2- 7 Black 1
B2+ ** RS422/RS485 Multifunction I/O terminal B2+ 8 Grey 1
OUT+ Output 1 and 2 supply input.
DO NOT connect >30V to this terminal !
9 Red 2
A2+ ** RS422/RS485 Multifunction I/O terminal A2+ 10 Violet 1
O1 Output 1. Can be used as digital output 11 Grey/pink 2
O2 Output 2. Can be used as digital output 12 Red/blue 2
AIN1
Analog input 1.
Can be used as analog input ±10V.
13 White/Green 1
AIN2
Analog input 2.
Can be used as analog input ±10V.
14 Brown/Green 1
RS232: RX
RS232 interface. Receive terminal
Leave open if unused.
15 White/Yellow 1
IO- Ground for IN1-4 and O1 and 2. Please notice
that this terminal is normally isolated from the
main ground and belongs to isolation group 2
16 Yellow/brown 2
RS232: TX
RS232 interface. Transmit terminal
Leave open if unused.
17 White/grey 1
“L/A IN” - Ethernet port connector - M12 - 4pin female connector “D” coded
Signal name Description Pin no.
JVL Cable
WI1046-
M12M4S05R
Isolation
group
(See note)
Tx0_P Ethernet Transmit channel 0 - positive terminal 1 Brown/White 3
Rx0_P Ethernet Receive channel 0 - positive terminal 2 Blue/White 3
Tx0_N Ethernet Transmit channel 0 - negative terminal 3 Brown 3
Rx0_N Ethernet Receive channel 0 - negative terminal 4 Blue 3
Shield Outside shield connected to connector housing Housing Shield 1
“L/A OUT” - Ethernet port connector. M12 - 4 pin female connector “D” coded
Signal name Description Pin no.
JVL Cable
WI1046-
M12M4S05R
Isolation
group
(see note)
Tx1_P Ethernet Transmit channel 1 - positive terminal 1 Brown/White 4
Rx1_P Ethernet Receive channel 1 - positive terminal 2 Blue/White 4
Tx1_N Ethernet Transmit channel 1 - negative terminal 3 Brown 4
Rx1_N Ethernet Receive channel 1 - negative terminal 4 Blue 4
Shield Outside shield connected to connector housing Housing Shield 1
* Note: Isolation group indicate which terminals/circuits that a galvanic connected to each other. In other
words group 1, 2, 3 and 4 are all fully independently isolated from each other. Group 1 correspond to the
housing of the motor which may also be connected to earth via the DC or AC input supply.
** No connection when module is mounted in a MAC050-MAC141.
To Next Page
Loading...