KB Electronics KBDA-24D - Limited Warranty

56 pages

To Previous Page

FLOMOTION SYSTEMS Inc.

165 Creekside Drive, Suite 112

Buffalo, NY 14228-2103

Tel:800-909-3569 (U.S. & Canada) or 716-691-3941

Fax:716-691-1253

SUPPORT:

Main Page

Table of Contents2
Quick-Start Instructions4
Quick-Start Connection Diagram4
Safety Warning6
Introduction7
Optional Accessories9
General Performance Specifications9
Electrical Ratings10
Keypad Layout with Main Speed Potentiometer10
Model KBDA-24D Drive Layout11
Model KBDA-27D Drive Layout12
Models KBDA-29, 45, 48 Drive Layout13
Model KBDA-24D Mechanical Specifications14
Models KBDA-27D, 29, 45, 48 Mechanical Specifications15
Important Application Information16
Maximum Allowed Motor Torque Vs. Speed16
Open Ventilated Motor with External Fan Cooling16
Mounting Instructions17
Electrical Connections17
Drive Terminal Block Wire and Tightening Torque Specifications18
Models KBDA-24D, 27D AC Line Input, Motor, and Ground Connections18
Multi-Function Output Relay Contacts19
Multi-Function Output Relay "Run" and "Fault" Operating Modes19
Models KBDA-29, 45, 48 AC Line Input, Motor, and Ground Connections19
Model KBDA-27D AC Line Input Voltage Selection (Jumper J1)20
Model KBDA-24D AC Line Input Voltage Selection (Jumper J1)20
AC Line Input Voltage Selection (Jumper J1 (Models KBDA-24D, 27D Only))20
Recommended High Voltage Dielectric Withstand Testing (Hi-Pot Testing)20
Typical Hi-Pot Test Setup21
Drive Operation21
Keypad Description22
Flow Chart to Program the Drive for 50 Hz Motors23
Flow Chart to Program Motor Current from 6.7 Amps to 5.5 Amps24
Flow Chart to Change Set Frequency from 5.00 Hz to 43.21 Hz25
Flow Chart to Program Accel Time from 1.5 Seconds to 120 Seconds26
Flow Chart to Program the Drive to Display Motor RPM27
Flow Chart to Program the Drive to Display Custom Units "012.028
Flow Chart Showing Motor Current, Motor Voltage, and Bus Voltage Added to the Basic Display29
Digital Readout Codes30
Function No. Description31
Programmable Function Summary List31
Model Software Revision Codes40
Diagnostic Leds41
LED Descriptions41
Appendix A - Optional IODA Input/Output Multi-Function Board42
IODA Status Indicator LED42
IODA Layout (All Models)43
IODA Terminal Block TB1 Layout43
IODA Terminal Block TB1 Wire and Tightening Torque Specifications43
IODA Functions and Features44
Preset Frequency Selection Switch or Contact Connections and Function Settings45
Preset Frequency Selection45
Up/Down Frequency Control Switch or Contact Connections and Function Settings46
Accel/Decel 2 Switch or Contact Connection and Function Settings46
Forward/Stop-Reverse/Stop Switch or Contact Connections and Function Settings47
External Fault Auxiliary Equipment Switch or Contact Connection and Function Setting47
Reset Switch or Contact Connection and Function Setting47
32 2-Wire Start/Stop Switch or Contact Connection and Function Settings48
33 3-Wire Start/Stop Switch or Contact Connection and Function Settings49
Analog Input 1 Signal Voltage Following Connection and Function Settings49
Analog Input 2 Signal Current Following Connection and Function Settings50
Analog Input 1 Electrical Ratings50
Analog Input 2 Electrical Ratings50
Analog Outputs 1 and 2 Connections and Function Settings51
Analog Outputs 1 and 2 Electrical Ratings51
Bidirectional Motor Operation Main Speed Potentiometer Connection and Function Setting52
Multi-Function Output Relay Contacts Connections and Function Settings53
Multi-Function Open Collector Connections and Function Settings54
Multi-Function Open Collector Outputs Electrical Ratings54
Limited Warranty56

KB Electronics KBDA-24D - Limited Warranty

Table of Contents

Related product manuals