Korg PA600 - Page 291

287
Effects
Reverb and Early Reflections (Reverb ER)
Appendix
76: Reverb BrightRoom
This room-type reverb emphasizes the early reflections that
make the sound brighter.
c: ER Level
d: Reverb Level
These parameters set the early reflection level and reverb level.
Changing these parameter values allows you to simulate the type
of walls in the room. That is, a larger “ER Level” simulates a hard
wall, and a larger “Reverb Level” simulates a soft wall.
77: Early Reflections
This effect is only the early reflection part of a reverberation
sound, and adds presence to the sound. You can select one of the
four decay curves.
a: Type
This parameter selects the decay curve for the early reflection.
a
Reverb Time
[sec]
0.1...3.0 Sets the reverberation time
High Damp [%] 0...100
Sets the damping amount in the
high range
b
Pre Delay
[msec]
0...200
Sets the delay time from the dry
sound
Pre Delay Thru
[%]
0...100
Sets the mix ratio of non-delay
sound
c ER Level 0...100 Sets the level of early reflections
d Reverb Level 0...100
Sets the reverberation level
e EQ Trim 0...100 Sets the EQ input level
f
Pre LEQ Fc
Low,
Mid-Low
Selects the cutoff frequency (low or
mid-low) of the low-range equalizer
Pre HEQ Fc
High,
Mid-High
Selects the cutoff frequency (high or
mid-high) of the high-range
equalizer
g
Pre LEQ Gain
[dB]
–15.0...+15.0 Sets the gain of Low EQ
Pre HEQ Gain
[dB]
–15.0...+15.0 Sets the gain of High EQ
h
Wet/Dry
Dry, 1:99...99:1,
Wet
Balance between the wet and dry
signal
Src Off...Tempo
Table , “Dynamic Modulation
sources,” on page 243
Amt –100...+100 Amount of modulation source
Left
Right
FX Amt
FX Amt
FX Amt = 100: Mono In - Stereo Out / FX Amt = 0: Stereo In - Stereo Out
EQ Trim
+
EQ Trim
LEQ HEQ
Pre Delay
Reverb
Reverb Level
ER Level
ER Level
Pre Delay Thru
ERs
ERs
Reverb - Room Type
Time
Level
Louder
ER
(Early Reflections)
Dry
Reverb
Pre Delay Thru
Pre Delay
Reverb Time
aType
Sharp, Loose,
Modulated,
Reverse
Selects the decay curve for the early
reflection
b ER Time [msec] 10...800
Sets the time length of early
reflection
c
Pre Delay
[msec]
0...200
Sets the time taken from the original
sound to the first early reflection
d EQ Trim 0...100
Sets the input level of EQ applied to
the effect sound
e
Pre LEQ Fc
Low,
Mid-Low
Selects the cutoff frequency (low or
mid-low) of the low-range equalizer
Pre HEQ Fc
High,
Mid-High
Selects the cutoff frequency (high or
mid-high) of the high-range
equalizer
f
Pre LEQ Gain
[dB]
–15.0...+15.0 Gain of the Low EQ
Pre HEQ Gain
[dB]
–15.0...+15.0 Gain of the High EQ
g
Wet/Dry
Dry, 1:99...99:1,
Wet
Balance between the wet and dry
signal
Src Off...Tempo
Table , “Dynamic Modulation
sources,” on page 243
Amt –100...+100 Amount of modulation source
Left
Right
FX Amt
FX Amt
FX Amt = 100: Mono In - Stereo Out / FX Amt = 0: Stereo In - Stereo Out
EQ Trim
+
EQ Trim
Pre Delay
Early Reflections
LEQ HEQ
Sharp
Loose
Modulated
Early Reflections - Type
Reverse
Dry
Pre Delay
ER Time