Kramer VP-550X

Kramer Electronics Ltd.
VP-550X - Protocol 3000
60
Function
Description
Syntax
Parameters/Attributes
Example
EQ-LVL?
Set equalization level.
COMMAND
#EQ-LVL?Stage, Channel, EqType<CR>
FEEDBACK
~nn@EQ-LVLStage, Channel, EqType, Level<CR><LF>
Stage – Input / Output
0 – Input
1 – Output
Channel – Number of channel
EgType – Equalizer Types
0 – Bass
1 – Middle
2 – Treble
Level– Equalizer level (±15DB for
the PA-120Z project)
Get Bass EQ level of the
speaker output to 12:
#EQ-LVLV1,2,2<CR>
ETH-PORT
Set Ethernet port
protocol.
If the port number you
enter is already in use, an
error is returned.
The port number must be
within the following range:
0-(2^16-1).
COMMAND
#ETH-PORTportType,port_id<CR>
FEEDBACK
~nn@ETH-PORTportType,port_id<CR><LF>
portType – TCP/UDP
Port_id – TCP/UDP port number
TCP – (5000-5099)
UDP – (50000-50999)
Set TCP port number to 5000:
#ETH-PORTTCP,5000<CR>
ETH-PORT?
Get Ethernet port
protocol.
COMMAND
#ETH-PORT?port_type<CR>
FEEDBACK
~nn@ETH-PORTport_type,port_id<CR><LF>
port_type – TCP/UDP
port_id –
when port_type = TCP:
5000~5099
when port_type = UDP:
50000~50999
Get the Ethernet port number
for UDP:
#ETH-PORT?UDP<CR>
FACTORY
Reset device to factory
default configuration.
This command
deletes all user data from
the device. The deletion
can take some time.
Your device may require
powering off and
powering on for the
changes to take effect.
COMMAND
#FACTORY<CR>
FEEDBACK
~nn@FACTORYOK<CR><LF>
Reset the device to factory
default configuration:
#FACTORY<CR>
HDCP-MOD
Set HDCP mode.
Set HDCP working
mode on the device input:
HDCP supported -
HDCP_ON [default].
HDCP not supported -
HDCP OFF.
HDCP support changes
following detected sink -
MIRROR OUTPUT.
When you define 3 as the
mode, the HDCP status is
defined according to the
connected output in the
following priority: OUT 1,
OUT 2. If the connected
display on OUT 2
supports HDCP, but OUT
1 does not, then HDCP is
defined as not supported.
If OUT 1 is not
connected, then HDCP is
defined by OUT 2.
COMMAND
#HDCP-MODstage,inp_id,mode<CR>
FEEDBACK
~nn@HDCP-MODstage,inp_id,mode<CR><LF>
stage – Input/Output
0 = Input
1 = Output
inp_id – Input number:
1 = HDMI 1
2 = HDMI 2
3 = HDMI 3
4 = HDMI 4
5 = HDMI 5
6 = HDMI 6
7 = HDMI 7
8 = USB-C
Output number
1 = HDMI1
2 = HDMI2
mode – HDCP mode
Input:
0 = Off
1 = On
Output:
2 = Follow input
3 = Follow output
Set the input HDCP-MODE of
input HDMI 1 to Off:
#HDCP-MOD0,1,0<CR>
HDCP-MOD?
Get HDCP mode.
Set HDCP working
mode on the device input:
HDCP supported -
HDCP_ON [default].
HDCP not supported -
HDCP OFF.
HDCP support changes
following detected sink -
MIRROR OUTPUT.
COMMAND
#HDCP-MOD?stage,inp_id<CR>
FEEDBACK
~nn@HDCP-MODstage,inp_id,mode<CR><LF>
stage – Input/Output
0 = Input
1 = Output
inp_id – Input number:
1 = HDMI 1
2 = HDMI 2
3 = HDMI 3
4 = HDMI 4
5 = HDMI 5
6 = HDMI 6
7 = HDMI 7
8 = USB-C
Output number
1 = HDMI1
2 = HDMI2
mode – HDCP mode
Input:
0 = Off
1 = On
Output:
2 = Follow input
3 = Follow output
Get the input HDCP-MODE of
input HDMI 1:
#HDCP-MOD?0,1<CR>
HELP
Get command list or help
for specific command.
COMMAND
#HELP<CR>
#HELPcommand_name<CR>
FEEDBACK
1. Multi-line:
~nn@Devicecommand,command…<CR><LF>
To get help for command use: HELP (COMMAND_NAME)<CR><LF>
~nn@HELPcommand:<CR><LF>
description<CR><LF>
USAGE:usage<CR><LF>
command – Name of a specific
command
Get the command list:
P<CR>
To get help for
AV-SW-TIMEOUT:
HELPAV-SW-TIMEOUT<CR>