EasyManua.ls Logo

Krone Swadro 807 - Maintenance; Special Safety Instructions; Compensation Springs Safety; Test Run Safety

Krone Swadro 807
94 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
Maintenance
65
Pos: 30.1 /Übersc hriften/Übersc hriften 1/U-Z/ Wartung @ 0\mod_ 11998835810 50_78.doc @ 36685
10 Maintenance
Pos: 30.2 /Übersc hriften/Übersc hriften 2/P-T/Spezi elle Sicher heitshinweise @ 0\mod_11966 60495760_78.d oc @ 9134
10.1 Special Safety Instructions
Pos: 30.3 /BA/Sich erheit/Gefahr enhinweise/Lad ewagen/Gefahr Wartung allg emein @ 0\mod _119988406986 2_78.doc @ 3670 4
Danger! - When performing repair, maintenance or cleaning work on the machine, or in
the case of technical intervention, drive elements may start moving.
Effect: Danger to life, injuries or damage to the machine.
Switch off the tractor engine and remove the ignition key
Secure the machine and tractor against the possibility of rolling back.
Switch off the PTO and disengage it
After the repair, maintenance and cleaning work or technical interventions are completed,
mount all protective coverings and safety devices properly again.
Avoid skin contact with oils, greases, cleaning agents and solvents.
In the event of injuries or burns due to oils, cleaning agents or solvents, contact a
physician immediately.
All other safety instructions must also be followed to avoid injuries and accidents.
Pos: 30.4 /Übersc hriften/Übersc hriften 2/A-E/Entl astungsfeder( n)@ 2\mod_1 20350898387 6_78.doc @ 66384
10.2 Compensation Spring(s)
Pos: 30.5 /BA/Sich erheit/Gefahr enhinweise/M ähwerke/Einstellu ng an den Entl astungsfedern @ 0\mod_11967 51594562_78. doc@ 12575
Danger! - Setting on the compensation springs
Effect: Danger to life or serious injuries
The compensation springs must only be removed in transport position. In the working
position the compensation springs are subject to high tensile stress.
Severe injury can be caused if the compensation springs are removed while in the
working position.
The lower threaded blocks on the compensation springs must be fully screwed in.
Pos: 30.6 /Übersc hriften/Übersc hriften 2/P-T/Pro belauf @ 0\m od_1196782963 921_78.doc @ 1 4908
10.3 Test run.
Pos: 30.7 /BA/Sich erheit/Gefahr enhinweise/M ähwerke/Verwen dung von nicht zug elassenen Ersa tzteilen @ 0\mod_11967 83037140_78.doc @ 14946
Danger! - Using non-approved spare parts.
Effect: Danger to life, serious injuries or loss of warranty claims as well as exclusion of liability
Use only authentic KRONE spare parts and accessories authorised by the manufacturer.
The use of spare parts, accessories or additional equipment not manufactured, tested or
approved by KRONE will exclude any liability for consequential damage.
Pos: 30.8 /BA/W artung/Hinweis V erschleiss verring ern @ 0\m od_1199953505 303_78.doc @ 37 204
Note
To ensure problem-free operation of the machine and to reduce wear and tear, specific
maintenance and upkeep intervals must be observed. These include cleaning, greasing,
lubricating and oiling parts and components.
Pos: 30.9 /BA/---- -Seitenumbruch--- --- @ 0\mod _1196175311 226_0.doc @ 416 5

Table of Contents

Related product manuals