2H5/2HS
2-3-5
Connector Pin Signal I/O Voltage Description
YC6 1 LED1 O 3.3/0 V DC Paper indicator display: On/Off
Connected
to the opera-
tion panel
PWB
2 LED2 O 3.3/0 V DC Jam indicator display: On/Off
3 SW I Analog Cancel key/GO key: On/Off
4 SGND - - Ground
5 LED3 O 3.3/0 V DC Ready indicator display: On/Off
6 LED4 O 3.3/0 V DC Attention indicator display: On/Off
7 LED5 O 3.3/0 V DC Toner indicator display: On/Off
8 LED6 O 3.3/0 V DC Data indicator display: On/Off
YC304 1 +3.3V2 O 3.3 V DC 3.3 V DC power source
Connected
to the MP
paper sen-
sor (duplex
model only)
2 SGND - - Ground
3 HANDSN I 0/3.3 V DC MP paper sensor: On/Off
YC305 1 +24V3 O 24 V DC 24 V DC power source
Connected
to the main
motor
2 PGND - - Ground
3 MMOTRDYN I 0/3.3 V DC Main motor ready signal
4 MMOTCLK O 0/3.3 V DC (pulse) Main motor clock signal
5 REMOTEN O 0/3.3 V DC Main motor: On/Off
YC306 1 SGND - - Ground
Connected
to the paper
sensor
2 +3.3V2 O 3.3 V DC 3.3 V DC power source
3 PAPER I 0/3.3 V DC Paper sensor: On/Off
YC307 1 +3.3V2 O 3.3 V DC 3.3 V DC power source
Connected
to the exit
sensor
2 SGND - - Ground
3 EXITN I 0/3.3 V DC Exit sensor: On/Off
YC308 1 +24V3 O 24 V DC 24 V DC power source
Connected
to the regis-
tration
clutch,
paper feed
clutch and
developing
clutch
2 REGDRN O 0/24 V DC Registration clutch: On/Off
3 +24V3 O 24 V DC 24 V DC power source
4 FEDDRN O 0/24 V DC Paper feed clutch: On/Off
5 +24V3 O 24 V DC 24 V DC power source
6 DLPDRN O 0/24 V DC Developing clutch: On/Off
YC309 1 +24V3 O 24 V DC 24 V DC power source
Connected
to the MP
paper feed
solenoid
(duplex
model only)
2 MPFDRN O 0/24 V DC MP paper feed solenoid: On/Off
YC311 1 +24V1 I 24 V DC 24 V DC power source
Connected
to the high
voltage
PWB
2 +3.3V1 O 3.3 V DC 3.3 V DC power source
3 ZCROSS I 0/3.3 V DC (pulse) Zero cross signal
4 FAN O 0/24 V DC Left cooling fan motor: On/Off
5 HEATN O 0/3.3 V DC Fuser heater lamp: On/Off
6 SLEEP O 0/3.3 V DC Sleep mode signal: On/Off
7 MHVDR O 0/3.3 V DC Main charger output signal: On/Off
8 RTHVDR O 0/3.3 V DC Transfer (reverse) bias output signal: On/Off
9 PSEL1 O 0/3.3 V DC Transfer (reverse) bias control signal: On/Off
10 HVCLK O 0/3.3 V DC (pulse) Developing bias clock signal
11 REGN I 0/3.3 V DC Registration sensor: On/Off
To Next Page
Loading...
