Why are printouts from my Kyocera TASKalfa 250ci wrinkled?
Wrinkled printouts from your Kyocera All in One Printer could be due to: * A dirty paper separator of the paper feed unit. Clean the paper separator. * Damp paper. Replace the paper with new paper.
Why are images skewed when printing from my Kyocera TASKalfa 250ci?
Skewed images from your Kyocera All in One Printer may be caused by: * Incorrectly placed originals on the platen. Align them with the original size indicator plates. * Incorrectly placed originals in the optional document processor. Align the original width guides securely before placing the originals. * Incorrectly loaded paper. Check the position of the paper width guides.
Why does my Kyocera TASKalfa 250ci All in One Printer often jam?
Frequent paper jams in your Kyocera All in One Printer could be due to: * Incorrectly loaded paper. Load the paper correctly. * Unsupported or poor condition paper. Remove the paper, turn it over, and reload it. * Curled, folded, or wrinkled paper. Replace the paper with new paper. * Loose scraps or jammed paper in the machine. Remove any jammed paper.
Why Kyocera TASKalfa 250ci All in One Printer cannot receive document?
There are several reasons the device might not be able to receive documents: * Make sure the modular cord is correctly connected. * If a communication error is displayed, resolve the error and ask the sender to retry. * If RX (reception) restriction is activated, cancel the RX restriction.
Why Kyocera TASKalfa 250ci All in One Printer cannot perform memory forwarding using a sub address?
The reasons why memory forwarding using a sub address may fail: * The recipient fax machine must have a sub address transmission feature for this function to work. * The entered sub address must match the one registered in the recipient fax machine. If your entry is correct, check with the recipient. Note: This machine does not use a sub address password for reception.
What to do if Kyocera All in One Printer displays 'FAX box limit exceeded'?
If the FAX Box limit is exceeded on your Kyocera All in One Printer, it means the FAX Box capacity is full with document data. Press [End] to cancel the job. To proceed, either print or delete the data in the FAX Box, and then try the job again.
Why are the printouts from my Kyocera TASKalfa 250ci All in One Printer dirty?
Dirty printouts from your Kyocera All in One Printer may be due to: * A dirty platen or document processor. Clean them. * A dirty transfer roller. Brush the transfer roller clean. * A dirty drum. Carry out Drum Refresh. * Carry out Developer Refresh. * A dirty scanner. Carry out Laser Scanner Cleaning. * The Printed Document Guard Kit being enabled. Disable the Printed Document Guard Kit.
How to fix light printouts on my Kyocera TASKalfa 250ci All in One Printer?
If your Kyocera All in One Printer's printouts are too light, consider the following: * If the machine is in Auto Density mode, set the correct density level for auto density. * If the machine is in Manual Density mode, use [Image Quality] to set the correct density level. * Shake the toner container from side to side several times to evenly distribute the toner. * If there is a message indicating the addition of toner, replace the toner container. * If the paper is damp, replace it with new paper. * Carry out Drum Refresh. * Carry out Developer Refresh. * Carry out Laser Scanner Cleaning. * If EcoPrint mode is enabled, disable it.
Why my Kyocera TASKalfa 250ci All in One Printer cannot print?
There could be several reasons why your Kyocera All in One Printer cannot print: * The power cord might not be plugged into an AC outlet. Plug it in. * The main power switch might not be turned on. Turn it on. * The printer cable might not be connected securely. Connect the correct printer cable securely. * The machine might have been powered on before the printer cable was connected. Power on the machine after connecting the printer cable. * 'Press Status Key...' might be displayed at the top of the screen. Press the Status/Job Cancel key, [Printing Jobs], and then [Resume All Print Jobs] to restart printing.
What to do if my Kyocera All in One Printer has a paper jam?
If a paper jam occurs, the Kyocera All in One Printer will stop, and the location of the jam will be indicated on the touch panel. Leave the machine on and follow the instructions to remove the jammed paper.
General| Functions | Print, Copy, Scan, Fax |
|---|---|
| Copy Resolution | 600 x 600 dpi |
| Duplex Printing | Standard |
| Type | Color Multifunctional |
| Print Speed | 25 ppm |
| Print Resolution | 600 x 600 dpi, Multi-bit technology for print quality of 9, 600 x 600 dpi equivalent |
| Copy Speed | 25 copies per minute (A4) |
| Scan Resolution | 600 dpi |
| Fax Resolution | 200 x 200 dpi, 300 x 300 dpi |
| Memory | 1 GB |
| Hard Disk Drive | 80 GB |
| Network Connectivity | Ethernet, USB |
| Scan Features | Scan to e-mail, Scan to FTP, Scan to SMB, Scan to USB Host, TWAIN scan |
To Next Page
