Lakeshore 331S - Command Summary

Lake Shore Model 331 Temperature Controller User’s Manual
Table 6-8. Command Summary
Command Function Page
QCLS Clear Interface Cmd ............................... 24
QESE Event Status Enable Cmd ...................... 24
QESE? Event Status Enable Query .................... 24
QESR? Event Status Register Query .................. 24
QIDN? Identification Query ................................ 24
QOPC Operation Complete Cmd ...................... 25
QOPC? Operation Complete Query .................... 25
QRST Reset Instrument Cmd ........................... 25
QSRE Service Request Enable Cmd ................ 25
QSRE? Service Request Enable Query .............. 25
QSTB? Status Byte Query .................................. 25
QTST? Self-Test Query ...................................... 26
QWAI Wait-To-Continue Cmd .......................... 26
ALARM Input Alarm Parameter Cmd .................. 26
ALARM? Input Alarm Parameter Query ................ 26
ALARMST? Input Alarm Status Query ....................... 26
ALMRST Reset Alarm Status Cmd ........................ 27
ANALOG Analog Output Parameter Cmd .............. 27
ANALOG? Analog Outputs Parameter Query .......... 27
AOUT? Analog Output Data Query ..................... 27
BAUD RS-232 Baud Rate Cmd ........................ 27
BAUD? RS-232 Baud Rate Query ...................... 27
BEEP System Beeper Cmd .............................. 28
BEEP? System Beeper Query ............................ 28
BRIGT Display Brightness Command ................ 28
BRIGT? Display Brightness Query ....................... 28
CMODE Control Loop Mode Cmd ........................ 28
CMODE? Control Loop Mode Query ...................... 28
CRDG? Celsius Reading Query .......................... 28
CRVDEL Delete User Curve Cmd ......................... 29
CRVHDR Curve Header Cmd ................................ 29
CRVHDR? Curve Header Query .............................. 29
CRVPT Curve Data Point Cmd ........................... 29
CRVPT? Curve Data Point Query ......................... 30
CSET Control Loop Parameter Cmd ................ 30
CSET? Control Loop Parameter Query .............. 30
DFLT Factory Defaults Cmd ............................ 30
DISPFLD Displayed Field Cmd .............................. 30
DISPFLD? Displayed Field Query ............................ 31
EMUL 330 Emulation Mode Cmd ...................... 31
EMUL? 330 Emulation Mode Query ................... 31
FILTER Input Filter Parameter Cmd .................... 31
FILTER? Input Filter Parameter Query .................. 31
Command Function Page
HTR? Heater Output Query .............................. 32
HTRST? Heater Status Query ............................... 32
IEEE IEEE Interface Parameter Cmd .............. 32
IEEE? IEEE Interface Parameter Query ............ 32
INCRV Input Curve Number Cmd ....................... 32
INCRV? Input Curve Number Query .................... 32
INTYPE Input Type Parameter Cmd .................... 33
INTYPE? Input Type Parameter Query .................. 33
KEYST? Keypad Status Query ............................. 33
KRDG? Kelvin Reading Query ............................. 33
LDAT? Linear Equation Data Query ................... 33
LINEAR Input Linear Equation Cmd ..................... 34
LINEAR? Input Linear Equation Query ................... 34
LOCK Front Panel Keyboard Lock Cmd ............ 34
LOCK? Front Panel Keyboard Lock Query ......... 34
MDAT? Min/Max Data Query ............................... 34
MNMX Min/Max Input Function Cmd .................. 35
MNMX? Min/Max Input Function Query ................ 35
MNMXRST Min/Max Function Reset Cmd ................ 35
MODE Set Local/Remote Mode ......................... 35
MODE? Query Local/Remote Mode ..................... 35
MOUT Control Loop MHP Output Cmd .............. 35
MOUT? Control Loop MHP Output Query ............ 35
PID Control Loop PID Values Cmd................ 36
PID? Control Loop PID Values Query ............. 36
RAMP Control Loop Ramp Cmd ........................ 36
RAMP? Control Loop Ramp Query ...................... 36
RAMPST? Control Loop Ramp Status Query ........... 36
RANGE Heater Range Cmd ................................. 37
RANGE? Heater Range Query .............................. 37
RDGST? Input Status Query .................................. 37
RELAY Relay Control Parameter Cmd ................ 37
RELAY? Relay Control Parameter Query ............. 37
RELAYST? Relay Status Query ................................ 37
REV? Input Firmware Revision Query .............. 38
SCAL Generate SoftCal Curve Cmd ................. 38
SETP Control Loop Setpoint Cmd .................... 38
SETP? Control Loop Setpoint Query .................. 38
SRDG? Sensor Units Reading Query .................. 38
TEMP? Room-Temp Comp. Temp. Query .......... 39
TUNEST? Control Loop 1 Tuning Query ................. 39
ZONE Control Loop Zone Table Cmd ............... 39
ZONE? Control Loop Zone Table Query ............. 39
Remote Operation 6-23