Lenze E82MV152_4B

Table of keywords
abc
15−2
L
EDB82MV752 EN 5.2
400 V/500 V, 3−10
operation with rated power
230 V, 3−5
400 V/500 V, 3−8
Cable specification, 4−6
Calibration, Application datum, 7−86
calling a password−protected function, 6−7
CAN bus identifier, 14−32
CAN bus node address, 14−31
Changeover, Setpoints, 7−47
Changing and saving parameters, with E82ZBC keypad, 5−3
Character format, 6−9
Check, before commissioning, 5−1
Chopper frequency reduction, 7−15
Code, 6−1
Code bank, 6−14
Code table, LECOM−A (RS232) communication module, 6−12
Codetabelle, Erläuterungen zur, 14−10
Codetabelle Antriebsregler, 14−10
Commissioning, 5−1
check before, 5−1
V/f characteristic control, 5−6
without function module, 5−6 , 5−8 , 5−10 , 5−12
Vector control, 5−10
Vector control optimisation, 5−14
Communication error, Reaction to, 14−21
Communication monitoring, LECOM−A (RS485) function
module, 6−14
Communication times, LECOM−A (RS232) communication
times, 6−10
Compensation equipment, interaction with, 4−5
Configuration
Acceleration times and deceleration times, 7−24
Actual value selection, 7−32
Analog input signals, 7−57
Analog output signals, 7−59
Analog outputs, 7−59
Analog process data output words, 7−64
Change of direction of rotation, 7−28
Communication monitoring, 14−21
Controller inhibit (DCTRL1−CINH), 7−20
Current limits, 7−23
Current−limit controller, 7−56
DC−injection brake (DCB), 7−30
Digital input signals, 7−68
Digital output signals, 7−73
Digital outputs, 7−73
Display functions, 7−86
Function library, 7−1
Manual / remote operation, 7−47
Maximum field frequency, 7−21
Minimum field frequency, 7−21
Monitoring functions
external faults, 7−85
Motor temperature, 7−82
Motor data detection, 7−48
Oscillation damping, 7−16
Parameter set changeover, 7−94
Process data output words, 7−79
Quick stop (QSP), 7−27
Relay output, 7−73
Setpoint selection, 7−32
Setpoint source selection, 7−32
Slip compensation, 7−13
Speed limit values, 7−21
Start conditions/flying−restart circuit, 7−18
switching frequency of inverter, 7−14
table of attributes, 14−51
Thermal motor monitoring, 7−82
TRIP reset, 7−85
TRIP set, 7−85
V/f rated frequency, 7−5
Vmin boost, 7−7
Conformity, 3−1
Control characteristics, Process controller, 7−50
Control connections
terminal assignment − application I/O, 4−12
terminal assignment − bus function modules, 4−16
terminal assignment − standard I/O, 4−9
Control mode, Selection, 5−4
Control word, 14−22
Controlled deceleration after mains failure, 7−19
Controller
Application as directed, 1−2
Labelling, 1−2
Controller inhibit, Drive performance, 7−18 , 7−20
Current derating
operation with increased rated power, 400 V/500 V, 3−10
operation with rated power, 400 V/500 V, 3−8
Current limits, 7−23
Current−limit controller, 7−56
Cyclic mains switching, 5−6 , 5−10
D
DC−bus connection, 10−1
Several drives, 10−1
DC−bus operation, 3−1
DC−injection brake, 7−30
Dead band
setting with auto DCB, 7−31
With analog setpoint selection, 7−35
Debouncing
Digital output signal "Torque threshold reached", 14−29