Linksys LAPAC1750PRO User Manual

24
Section 3: Configuring the Access Point
LAPAC1750PRO Access Point Software User Manual
From Email Address Specify the email address that appears in the From
field of alert messages sent from the AP, for example
AP23@foo.com. The address can be a maximum
of 255 characters and can contain only printable
characters. By default, no address is configured.
Log Duration This duration, in minutes, determines how frequently
the non critical messages are sent to the SMTP
Server. The range is 30-1440 minutes. The default is
30 minutes.
Urgent Message
Severity
Configures the severity level for log messages
that are considered to be urgent. Messages in this
category are sent immediately. The security level you
select and all higher levels are urgent:
• Emergency indicates system is unusable. It is the
highest level of severity.
• Alert indicates action must be taken
immediately.
• Critical indicates critical conditions.
• Error indicates error conditions.
• Warning indicates warning conditions.
• Notice indicates normal but significant
conditions.
• Informational indicates informational messages.
• Debug indicates debug-level messages.
Non Urgent Severity Configures the severity level for log messages that
are considered to be non urgent. Messages in this
category are collected and sent in a digest form at
the time interval specified by the Log Duration field.
The security level you select, and all levels up to but
not including the lowest urgent level, are considered
non-urgent. Messages below the security level you
specify are not sent via email.
See the Urgent Message field description for
information about the security levels.
Mail Server Configuration
Mail Server Address Specify the IP address or hostname of the SMTP
server on the network.
Mail Server Security Specify whether to use SMTP over SSL (TLSv1) or
no security (Open) for authentication with the mail
server. The default is TLSv1.
Mail Server Port Configures the TCP port number for SMTP. The range
is a valid port number from 0 to 65535. The default is
“465”, which is the standard port for SMTP.
Username Specify the username to use when authentication
with the mail server is required. The username is a
64-byte character string with all printable characters.
The default is “admin”.
Password Specify the password associated with the username
configured in the previous field.
Message Configuration
To Address 1 Configure the first email address to which alert
messages are sent. The address must be a valid email
address. By default, no address is configured.
To Address 2 Optionally, configure the second email address to
which alert messages are sent. The address must
be a valid email address. By default, no address is
configured.
To Address 3 Optionally, configure the third email address to
which alert messages are sent. The address must
be a valid email address. By default, no address is
configured.
Email Subject Specify the text to be displayed in the subject of the
email alert message. The subject can contain up to
255 alphanumeric characters. The default is “Log
message from AP”.

Linksys LAPAC1750PRO Specifications

General

Modulation	-
VLAN support	Yes
Frequency band	2.4, 5 GHz
Number of users	- user(s)
Channels quantity	- channels
Networking standards	IEEE 802.11a, IEEE 802.11ac, IEEE 802.11b, IEEE 802.11g, IEEE 802.11n, IEEE 802.3, IEEE 802.3ab, IEEE 802.3at, IEEE 802.3u
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Maximum data transfer rate	1750 Mbit/s
Internal	No
Certification	FCC, CE, IC
Product color	White
Cable lock slot type	Kensington
Ethernet LAN (RJ-45) ports	2
Security algorithms	802.1x RADIUS, WEP, WPA, WPA2
Antenna gain level (max)	5.2 dBi
Input current	2 A
AC input voltage	12 V
Power consumption (typical)	24 W
Storage temperature (T-T)	-20 - 70 °C
Operating temperature (T-T)	0 - 35 °C
Storage relative humidity (H-H)	10 - 90 %
Operating relative humidity (H-H)	10 - 85 %

Weight and Dimensions

Depth	238 mm
Width	247 mm
Height	43.3 mm
Weight	520 g