- 6 -
FOCS Workshop Manual_cod. 1.5302.351_7° ed_ rev. 06
-
Crankshaft timing pulley ................................................................................................................................................... 36
Crankshaft, check journals and crank .............................................................................................................................. 63
Crankshaft, lubrication lines ............................................................................................................................................. 63
Cylinder head assembly ................................................................................................................................................... 57
Cylinder head tightening procedure LDW 1204-1204/T-1404 ........................................................................................ 57
Cylinder head tightening procedure LDW 502-602-702-903-1003 ................................................................................. 57
CYLINDER HEAD, removal .............................................................................................................................................. 48
Cylinder roughness ........................................................................................................................................................... 59
Cylinder, class ................................................................................................................................................................... 59
CYLINDERS ......................................................................................................................................................................59
Driving pulley .................................................................................................................................................................... 34
Dry type air filter ...............................................................................................................................................................29
E.G.R. Circuit .............................................................................................................................................................. 30-31
Exhaust maniflod .............................................................................................................................................................. 32
Flywheel ............................................................................................................................................................................ 34
Fuel rail ............................................................................................................................................................................. 44
Fuel tank (optional) ........................................................................................................................................................... 33
Governor springs .............................................................................................................................................................. 40
Governor springs for Gensets .......................................................................................................................................... 40
Head gasket ...................................................................................................................................................................... 56
Hydraulic pump drive ........................................................................................................................................................65
Injection pump control rod ................................................................................................................................................ 44
Intake / Exhaust / Injection camshaft lobe height - LDW 903 ........................................................................................ 47
Intake manifold – Remote air filter ................................................................................................................................... 30
Journal and connecting rod pins diameters ..................................................................................................................... 63
Main bearings and connecting rod big ends diameters .................................................................................................. 64
Oil bath air cleaner ( on request ).................................................................................................................................... 29
Oil pan, removal ............................................................................................................................................................... 52
Oil pump - disassembly ....................................................................................................................................................42
Oil pump - Reassembly .................................................................................................................................................... 42
PISTON ............................................................................................................................................................................. 52
Piston clearance ...............................................................................................................................................................55
Piston coolant nozzles ...................................................................................................................................................... 61
Piston ring, Clearance between grooves ......................................................................................................................... 54
Piston ring, mounting order .............................................................................................................................................. 55
Piston rings - End gaps ....................................................................................................................................................54
Piston, assembly ............................................................................................................................................................... 55
Piston, class ......................................................................................................................................................................53
Piston, disassembly and inspection................................................................................................................................. 53
Piston, weight .................................................................................................................................................................... 54
Pre-combustion chamber .................................................................................................................................................51
Pre-combustion chamber ring nut removal ..................................................................................................................... 51
Pre-combustion chamber, installation ............................................................................................................................. 51
Pre-combustion chamber, removal ..................................................................................................................................51
Pump/injector unit - Disassembly .................................................................................................................................... 45
Pump/injector unit - non-return valve............................................................................................................................... 45
Rear and forward main bearing caps............................................................................................................................... 60
RECOMMENDATIONS FOR DISASSEMBLING AND ASSEMBLING ........................................................................... 28
RECOMMENDATIONS FOR OVERHAULS AND TUNING ............................................................................................ 28
Return pulley ..................................................................................................................................................................... 34
Ringfeder-type rings on LDW 1204-1204/T-1404 ........................................................................................................... 35
Ringfeder-type rings on LDW 1204-1204/T-1404 - Assembly ........................................................................................ 35
Rocker arm assembly ....................................................................................................................................................... 45
Rocker arm cover.............................................................................................................................................................. 42
Rocker arm cover gasket .................................................................................................................................................. 43
Rocker arm pivot, dismounting and remounting ............................................................................................................. 46
Shoulder half rings ............................................................................................................................................................ 61
Shoulder half rings, oversized elements .......................................................................................................................... 62
Speed governor .................................................................................................................................................................40
Speed governor - Limiting speed governor ...................................................................................................................... 41
Speed governor - Reassembly ......................................................................................................................................... 41
Speed governor components ........................................................................................................................................... 40
Stop pin rings, dismounting and remounting................................................................................................................... 52
Third drive, components ................................................................................................................................................... 65
Tightening pulley ............................................................................................................................................................... 36
Timing belt / Timing pulley arrangement ......................................................................................................................... 36
Timing belt cover ..............................................................................................................................................................35
Chapter index
To Next Page
Loading...
Need help?
General
