To Next Page

To Previous Page

3-93-9



A - DAIL

A - DAILY OR EVERY 10 Y OR EVERY 10 HOURS SERVICEHOURS SERVICE

A1 - I.C. ENGINE OIL LEVELA1 - I.C. ENGINE OIL LEVEL

CHECKCHECK

Place the lift truck on level ground with the I.C. engine stopped, and let the oil drain intoPlace the lift truck on level ground with the I.C. engine stopped, and let the oil drain into

the sump.the sump.

- Open the I.C. engine bonnet.- Open the I.C. engine bonnet.

- Remove the dipstick 1 (fig. A1).- Remove the dipstick 1 (fig. A1).

- Clean the dipstick and check the correct level between the two notches.- Clean the dipstick and check the correct level between the two notches.

-- If necessary, add oil (see: 3 - MIf necessary, add oil (see: 3 - MAINTENANCE: LUBRICANTS AND FUEL) by tAINTENANCE: LUBRICANTS AND FUEL) by the filler port 2he filler port 2

(fig. A1).(fig. A1).

-- Check visually that there is no leakage Check visually that there is no leakage or seepage of oil in the I.or seepage of oil in the I.C. engine.C. engine.

A2 - COOLING LIQUID LEVELA2 - COOLING LIQUID LEVEL

CHECKCHECK

Place the lift truck on level ground with the I.C. engine stopped, and allow the I.C. enginePlace the lift truck on level ground with the I.C. engine stopped, and allow the I.C. engine

to cool.to cool.

- Open the I.C. engine bonnet.- Open the I.C. engine bonnet.

- Check the correct level in the middle of gauge 1 (fig. A2).- Check the correct level in the middle of gauge 1 (fig. A2).

-- If necessary, add cooling liquid (see: If necessary, add cooling liquid (see: 3 - MAINTENANCE: LUBRICANTS AND 3 - MAINTENANCE: LUBRICANTS AND FUEL).FUEL).

- Slowly turn the - Slowly turn the cap of the radiator 2 (fig. A2) cap of the radiator 2 (fig. A2) up to the safety stop.up to the safety stop.

- Allow the pressure and the steam to escape.- Allow the pressure and the steam to escape.

- Press down and turn the cap so as to release it.- Press down and turn the cap so as to release it.

-- Add cooling liquid via filler port 3 (fig. A2) up to the middle of gauge 1 (Add cooling liquid via filler port 3 (fig. A2) up to the middle of gauge 1 (fig. A2).fig. A2).

-- Lubricate slightly the filler necLubricate slightly the filler neck in order to facilitate thk in order to facilitate the setting and the e setting and the removal of theremoval of the

radiator cap.radiator cap.

- Check visually that there is no leakage in the radiator and pipes.- Check visually that there is no leakage in the radiator and pipes.

To avoid any risk of spraying or burning, wait until the To avoid any risk of spraying or burning, wait until the I.C. engine has cooled down before removing the cooling circuit filler I.C. engine has cooled down before removing the cooling circuit filler plug. If the cooling liquid isplug. If the cooling liquid is

very hot, add only hot cooling liquid (80°C). In an emergency, you can use water as a cooling liquid, then change the cooling circuit liquid as soon asvery hot, add only hot cooling liquid (80°C). In an emergency, you can use water as a cooling liquid, then change the cooling circuit liquid as soon as

possible (see: 3 - MAINTENANCE: F1 - possible (see: 3 - MAINTENANCE: F1 - COOLING LIQUID).COOLING LIQUID).

A3 - FUEL LEVELA3 - FUEL LEVEL

CHECKCHECK

Keep the fuel tank full, to reduce as much as possible any condensation due to theKeep the fuel tank full, to reduce as much as possible any condensation due to the

atmospheric conditions.atmospheric conditions.

- Open the access panel for hydraulic oil filling.- Open the access panel for hydraulic oil filling.

- Remove cap 1 (fig. A3).- Remove cap 1 (fig. A3).

-- Fill the fuel tank with clean fuFill the fuel tank with clean fuel (see: 3 - MAINTENANCE: LUel (see: 3 - MAINTENANCE: LUBRICANTS AND FUEL), BRICANTS AND FUEL), filteredfiltered

through a strainer or a clean, lint free cloth, through filler port 2 (fig. A3).through a strainer or a clean, lint free cloth, through filler port 2 (fig. A3).

- Put back the cap 1 - Put back the cap 1 (fig. A3) and close the fuel filler (fig. A3) and close the fuel filler access panel.access panel.

- Check visually that there is no leakage in the tank and pipes.- Check visually that there is no leakage in the tank and pipes.

Never smoke or approach with a flame during filling operations or when the tank is open. Never refillNever smoke or approach with a flame during filling operations or when the tank is open. Never refill

while I.C. engine is running.while I.C. engine is running.

The fuel tank is degassed via the filler The fuel tank is degassed via the filler plug. When changing it, always use an original part, plug. When changing it, always use an original part, with degassing hole.with degassing hole.

A1A1

A3A3

A2A2

https://www.forkliftpdfmanuals.com/