Mankati FULLSCALE XT PLUS - Fix Horrible

www.mankati.com
26
Parameter Definition
Infill
-Solid infill top: Create a solid top surface, if set to false the top
islledwiththellpercentage.Disablethisfeatureandsetll
densityas0toprintcups/vasesthatarewithouttopmodel.
-Solid infill bottom: Create a solid bottom surface, if set to false
thebottomislledwiththellpercentage.Disablethisfeature
andsetlldensityas0toprintbuildingsthatarewithoutbottom
model.
-Infill overlap: Amountofoverlapbetweentheinllandthe
walls.Thereisaslightoverlapwiththewallsandtheinllsothe
wallsconnectrmlytotheinll.Recommendedsettingas10
withbestperformance.Toobigwillinuencequalityofmodel
surface.
Support
-Structure type: See function prompt in the software
-Overhang angle for support: See function prompt in the
software
-Fill amount: Supportprintdensity.
Recommendedsettingas15withbestperformance.More
densitymakesthesupportnoteasytoremove.Lessdensity
inuencesprintquality.
-Distance X/Y: Distance of the support material from the print,
intheX/Ydirections.0.7mmgivesanicedistancefromtheprint
sothesupportdoesnotsticktotheprint.Toofarwillinuence
supportperformance.
-Distance Z: Distancefromthetop/bottomofthesupport
totheprint.Asmallgapheremakesiteasiertoremovethe
supportbutmakestheprintabituglier.0.15mmgivesagood
separationofthesupportmaterial.Toofarwillinuencesupport
performance.
Spiralize
-
Spiralize the outer contour: Spiralize is smoothing out the Z
moveoftheouteredge.ThiswillcreateasteadyZincrease
overthewholeprint.Thisfeatureturnsasolidobjectintoa
singlewalledprintwithasolidbottom.
When enabling this feature, the top will not be printed and
automaticallysettinginllas0.
Black Magic
-Spiralize the outer contour: New function in MankatiUM
6.5.SpiralizeissmoothingouttheZmoveoftheouteredge.
ThiswillcreateasteadyZincreaseoverthewholeprint.This
feature turns a solid object into a single walled print with a solid
bottom.Whenenablingthisfeature,thetopwillnotbeprinted
andautomaticallysettinginllas0.
-Only follow mesh surface: newfunctioninMankatiUM6.5.
Seefunctionpromptinthesoftware.
Birm
-Birm line amount: Defaultas5,morelines,morermlythe
modelstickingtoplatform.
Raft
-Extra margin: If the raft is enabled, this is the extra raft area
aroundtheobjectwhichisalsorafted.
-Line spacing:Seefunctionpromptinthesoftware.
-Base thickness:Seefunctionpromptinthesoftware.
-Base line width:Seefunctionpromptinthesoftware.
-Interface thickness:Seefunctionpromptinthesoftware.
-Interface line width:Seefunctionpromptinthesoftware.
-Airgap: Seefunctionpromptinthesoftware.
-First Layer Airgap:Seefunctionpromptinthesoftware.
-Surface layer:Seefunctionpromptinthesoftware.
-Surface layer thickness: Seefunctionpromptinthesoftware.
-Surface layer line width: Seefunctionpromptinthesoftware.
Fix Horrible
Combing ererything ( Type-A )/( Type-B ):
Thisexpertoptionaddsallpartsofthemodeltogether.The
resultisusuallythatinternalcavitiesdisappear.Dependingon
themodelthiscanbeintendedornot.Enablingthisoptionis
atyourownrisk.Type-Aisdependedonthemodelnormals
andtriestokeepsomeinteralholesintace.Type-Bignoresall
internalholesandonlykeepstheoutsideshperperlayer.
Keep open faces:
Thisexpertoptionkeepsalltheopenbitsofthemodelintact.
Normally Mankati Tries to stitch up small holes and remove
everything with big holes, but this option keeps bits that are
not properly part of anything and just goes with whatever it is
enable you to slice models otherwise failing to produce proper
paths.Aswithall"Fixhorrible"options,resultsmayvaryand
useatyourownrisk.
Extensive stitching:
Extrensivesitichingtriestoxupopenholesinthemodelby
closingtheholewithtouchingpolygons.Thisalgorthmisquite
expensiveandcloudintroducealotofprocessingtime.Aswith
all "Fix horrible" options, results may vary and use at your own
risk.