ENGLISH
TUNER
OPERATION
LISTENING
TO
THE
TUNER
Frequency scan step for
AM
is
selectable.
Default setup is
10kHz
step, if your country's
standard
is
9 kHz step, Press BAND button
on
the
remote controller more than 6 seconds. Scan step
will change.
Note:
Preset memory for the tuner will clear by changing
this setup.
MANUAL
TUNING
1.
2.
-~
...
a
..
a~n
-
..<
......
-
-
--
~
=
:>
C;
0
CSLl
ccJ=T2.
TUHE-
6-1.
(FM)
TUNING
MODE
(AUTO
STEREO
OR
MONO)
rnapanlZ
-
.r?\:J~
o 0 0
'\.v'
0 0
AUTO
TUNING
1.
2.
....
apan.z
CSLl
ceLT
2.
TUNE-
6-1.
(Using the unit)
1.
To
select tuner and desired band (FM or AM),
press the BAND button
on
the front panel.
2. Press the
TUNING/PRESET.
or T buttons
on
the front panel for more than 1 second to start
the auto tuning function.
3. Automatic searching begins then stops when a
station
is
tuned
in.
(Using the remote controller)
1.
To
select
tuner
and desired band (FM or
AM), press the BAND button
on
the remote
controller.
2. Press the TUNE +
or
-
(.
or
T)
for more than 1
second
on
the remote controller.
3. Automatic searching begins then stops when a
station
is
tuned
in.
If
tuning does not stop at the desired station, use
to
the "Manual tuning" operation.
(Using the unit)
1.
To
select tuner and desired band
(FM
or AM),
press the BAND button
on
the front panel.
2. Press the
TUNING/PRESET.
or
T buttons
on
the front panel
to
select the desired station.
(Using the remote
controller)
1.
To
select tuner and desired band (FM or
AM), press the BAND button
on
the remote
controller.
2. Press the TUNE +
or
-
(.
or
T)
on
the remote
controller
to
tune
in
the desired station.
DIRECT
F~QUENCY
CALL
.-
I
&-1.
r~f~Ir~13
I
I'
:~~0~J
:I()\:
l~}
8--,2.
1.
To
select tuner and desired band (FM or
AM), press the BAND button
on
the remote
controller.
2. Press the F.DIRECT
on
the remote controller,
display will show "FREQ - - - .".
3. Input your desired station's frequency with the
numeric buttons
on
the remote controller.
4. The desired station will automatically
be
tuned.
When
in
the auto stereo mode, AUTO indicator will
be
illuminated
on
the display.
The "ST" indicator is illuminated when a stereo
broadcast
is
tuned
in.
At open frequencies, the noise
is
muted and the
"TUNED" and "ST" indicators are not illuminated.
If
the signal
is
weak,
it
may
be
difficult
to
tune into
the station in stereo.
In
such a case, press the
T-MODE
button
on
the
front
panel
or
remote
controller.
"AUTO" indicator is not illuminated, if
FM
stereo
broadcasts are received
in
monaural and the "ST"
indicator
is
not illuminated.
To
return
to
auto stereo mode, press the T-MODE
button or press T·MODE button
on
the remote
controller again. AUTO indicator
is
illuminated
on
the
display.
To Next Page
Loading...
