Metrohm 794 Basic Titrino - Page 100

3.2. Remote control commands
794 Basic Titrino
96
│ │ ├ .C45 Start volume read only/read+write
│ │ ├ .C46 Asymmetry pH read only
│ │ ├ .C47 Slope of electrode read only
│ ├ .FixEP Fix EP
│ │ ├ .51 C51
│ │ │ ├ .Value Value read only 3.2.2.72.
│ │ │ up to 59
│ ├ .pK pK/HNP
│ │ ├ .61 C61
│ │ │ ├ .Value Value read only ditto
│ │ │ up to 69
│ ├ .TempVar Temporary variables C7X
│ │ ├ .C70 up to C79 read only/read+write ditto
│
├ .StatisticsVal Statistics values
│ ├ .ActN Number of results in chart read only 3.2.2.73.
│ ├ .1 1
st
mean
│ │ ├ .Mean Mean read only ditto
│ │ ├ .Std Absolute standard deviation read only ditto
│ │ ├ .RelStd Relative standard deviation read only ditto
│ ├ up to 9 mean values
│
├ .SiloCalc Values of silo calculations
│ ├ .C24 Values of variable C24
│ │ ├ .Name Name read only 3.2.2.74.
│ │ ├ .Value Value read only ditto
│ │ ├ .Unit Unit read only ditto
│ ├ .C25 as for C24
│ ├ .C26 Values of variable C26
│ │ ├ .ActN Number of single values read only ditto
│ │ ├ .Mean Mean value read only ditto
│ │ ├ .Std Absolute standard deviation read only ditto
│ │ ├ .RelStd Relative standard deviation read only ditto
│ ├ .C27 as for C26
│ "Info", continuation
├ .ActualInfo Current data
│ ├ .Inputs I/O Inputs
│ │ ├ .Status Line status read only 3.2.2.75.
│ │ ├ .Change Change of line status read only ditto
│ │ ├ .Clear Clear change $G ditto
│ ├ .Outputs as for I/O Inputs ditto
│ ├ .Assembly From Assembly
│ │ ├ .CyclNo Cycle number read only 3.2.2.76.
│ │ ├ .Counter Assembly counter read only 3.2.2.77.
│ │ │ ├ .V Volume counter read only ditto
│ │ │ ├ .Clear Clears counter $G ditto
│ │ ├ .Meas Measured value read only 3.2.2.78.
│ ├ .Titrator From Titrator
│ │ ├ .CyclNo Cycle number read only 3.2.2.79.
│ │ ├ .V Volume read only ditto
│ │ ├ .Meas Measured indicator voltage read only ditto
│ │ ├ .dVdt Volume drift dV/dt read only ditto
│ │ ├ .dMeasdt Measured value drift read only ditto
│ │ ├ .dMeasdV 1st deviation of titration curve read only ditto
│ │ ├ .ERC ERC from DET read only ditto
│ ├ .MeasPt Entry in measuring point list
│ │ ├ .Index Index of entry read only 3.2.2.80.
│ │ ├ .X X coordinate read only ditto