o Data insert instruction
"I"
# I . X X X X CR
LF
-T
-
5 2 3
, I I
r-1
I
X X X
X600661166------
6
F
F6CR
LF
. - -
,--
Up
to
16 bytes
X X
Y X 6 CR CR LF #
-----L..J---
4
1. I nsert
start
address
2. Data
to
be inserted
3. Data separate mark
4. End code
5. I nsert address
o CONT instructions
"OT"
and
"OTn"
ji. 0 T CR
---,-Normal
CR LF #
LAbnormal
CR
LF ?
CR
LF #
"OTn"
block CONT instruction
#OT
nCR
Same
as
the
OT instruction.
o Buffer check sum instruction
"BO"
Sample
output
of a check sum for a range specified using
PAE
#BOCR
882C64E
~
L--Exclusive
OR
IL
_____
Addition
#BOCR
LF~~~g:::~~CR
LF!
o PROM device select instruction
"N"
Selected by entering
the
number assigned
to
a P·ROM.
(See a command number.)
#N
6
00
-
CR
-1-
I
If
oo'y
CR
h"
be"
,ow,d,
th,
device
is
not
changed.
The
current
device number
is
dis-
played.
#N600-CCR
-1-
I s.mp" 27128
hl,h<pe.d
p,o""m-
ming specification.
The
current
device number
is
dis-
played.
For the device number, two entered lower digits are valid.
If only one digit has been entered, the second digit
is
assumed
to
be
"0".
ji. N::: 0 O:..n n
CRiNormal
LAbnormal
CR
LFit.
CR
LFICR
LFtt.
o Address select instruction
"A"
46
This selects
the
all
address
(N)
mode, the even (E) mode
or the odd (0) mode
as
the operation address mode.
#A606CR
-1-
Lif
oo'y
CR
h"
be"
•
ol."d
,
th,
address mode
is
not
changed.
The
current
address mode
is
displayed:
#A6
N6
E CR
N:
All
address mode
E:
Even address mode
0:
Odd address mode
-
-1-
~Specifies
the even address mode.
L-----At
present, the
all
address mode
is
established.
o
In
the address mode, only
"N",
"0"
and
"E"
may be
entered
as
input
data. The
other
data
is
considered
to
be
an
error.
o EEP-ROM chip erase instruction
"Z"
Chip-erases an EEP-ROM. For the EP-ROM, the instruc-
tion
is
not
accepted.
#ZCR
#Z
CR-~--Normal
LAbnormal
CR
LF#
o EEP-ROM byte erase instruction
"ZB"
Byte-erases
an
EEP-ROM. For any device which
cannot
be
byte-erased,
the
instruction
is
not
accepted.
#ZB
CR
ADRS-10CR
- - - -
~Address
to
be erased.
!ZBCR
LF~Q!!.§..-1
OCRTNormal
LAbnormal
8-7 Instructions
in
Serial Mode
CR
LF
#
---
CR
LF
1
CR
LF.it.
The serial instruction
for
the
Programmer permits exchanging
data with an external
equipment
through key operations.
Data exchange
is
activated by a specified data format.
(Note
1)
The serial instruction offers four functions.
o Receives a data format
sent
from
an
external equipment.
o Outputs a data format from
the
Programmer
to
an exter-
nal
equipment.
o
Outputs
a list from the Programmer
to
an external equip-
ment.
o Outputs a control code from
the
Programmer
to
an exter-
nal equipment.
Note
1:
See 9-8, Data Format. The format
is
specified by
"EDIT",
"FORMAT"
and "FORMAT
No."
keys.
To Next Page
Loading...