Mitsubishi Electric Q26UD(E)HCPU - Page 520

518
SD100
Transmission
speed
storage area
Transmission
speed set in
parameter
This register stores the transmission speed set in parameter
when the serial communication function is used.
12: 1200bps, 24: 2400bps, 48: 4800bps, 96: 9600bps, 192:
19200bps, 384: 38400bps, 576: 57600bps, 1152: 115200bps
S (Power-
ON or
reset)
New
Q00/Q01
QnU
*4
LCPU
*7
SD101
Communicati
on setting
storage area
Communicati
on setting set
in parameter
This register stores the communication setting set in
parameter when the serial communication function is used.
S (Power-
ON or
reset)
New
Q00/Q01
QnU
*4
LCPU
*7
SD102
Transmission
wait time
storage area
Transmission
wait time set
in parameter
This register stores the transmission wait time set in
parameter when the serial communication function is used.
0: No waiting time
10 to 150: Waiting time (unit: ms)
Default: 0
S (Power-
ON or
reset)
New
Q00/Q01
QnU
*4
LCPU
*7
SD105
CH1
transmission
speed setting
(RS-232)
Transmission
speed (RS-
232)
This register stores a transmission speed. (If no external
device is connected, the default value, 1152, is stored.)
96: 9600bps, 192: 19200bps, 384: 38400bps, 576: 57600bps,
1152: 115200bps
SNew
Qn(H)
QnPH
QnPRH
This register stores a transmission speed. (If no external
device is connected, the default value, 1152, is stored.)
This register stores a transmission speed set in parameter
when the serial communication function is used
*8
.
96: 9600bps, 192: 19200bps, 384: 38400bps, 576: 57600bps,
1152: 115200bps
SNew
QnU
*3
This register stores a transmission speed. (When the
L02SCPU, L02SCPU-P, or RS-232 adapter is used, the
default value, 1152, is stored.)
This register stores a transmission speed set in parameter
when the serial communication function is used.
96: 9600bps, 192: 19200bps, 384: 38400bps, 576: 57600bps,
1152: 115200bps
SNewLCPU
SD110
Data sending
result storage
area
Data sending
result
This register stores the error code if an error occurs during
data transmission when the serial communication function is
used.
S (Error) New
Q00/Q01
QnU
*4
LCPU
*7
SD111
Data
receiving
result storage
area
Data
receiving
result
This register stores the error code if an error occurs during
data reception when the serial communication function is
used.
S (Error) New
Q00/Q01
QnU
*4
LCPU
*7
SD118
Amount of
battery
consumption
Amount of
battery
consumption
This register stores a battery consumption rate.
[Value range]
• 1 or 2: Q00UJCPU, Q00UCPU, Q01UCPU, Q02UCPU,
Q03UD(E)CPU, Q04UD(E)HCPU, L02SCPU, L02SCPU-P,
L02CPU, L02CPU-P
• 1 to 3: Q06UD(E)HCPU, L06CPU, L06CPU-P, L26CPU,
L26CPU-P, L26CPU-BT, L26CPU-PBT
• 1 to 4: Q10UD(E)HCPU, Q20UD(E)HCPU,
Q13UD(E)HCPU, Q26UD(E)HCPU
• 1 to 5: Q50UDEHCPU, Q100UDEHCPU
S (Status
change)
New
QnU (except
QnUDV)
LCPU
Number Name Meaning Explanation
Set by
(When Set)
Corresponding
ACPU
D9
Corresponding
CPU
b0
to
b3b4b5b6
b15
to
Sumcheck presence
0: Absent
1: Present
0: Disabled
1: Enabled
Write during RUN setting
Since this area is reserved for
a system, storage data are variable.
Since this area is
reserved for a system,
storage data are variable.