A - 5 A - 5
5.3.5 Setting devices (except for annunciators) (SET) ............................................................................5 - 28
5.3.6 Resetting devices (except for annunciators) (RST)........................................................................ 5 - 30
5.3.7 Setting and resetting the annunciators (SET F, RST F).................................................................5 - 32
5.3.8 Leading edge and trailing edge output (PLS, PLF).........................................................................5 - 34
5.3.9 Bit device output reverse (FF).........................................................................................................5 - 36
5.3.10 Pulse conversion of direct output (DELTA, DELTAP) .................................................................. 5 - 38
5.4 Shift Instruction.......................................................................................................................................5 - 40
5.4.1 Bit device shift (SFT, SFTP)............................................................................................................5 - 40
5.5 Master Control Instructions ....................................................................................................................5 - 42
5.5.1 Setting and resetting the master control (MC, MCR)...................................................................... 5 - 42
5.6 Termination Instructions.........................................................................................................................5 - 46
5.6.1 End main routine program (FEND) .................................................................................................5 - 46
5.6.2 End sequence program (END)........................................................................................................ 5 - 48
5.7 Other Instructions...................................................................................................................................5 - 50
5.7.1 Sequence program stop (STOP) ....................................................................................................5 - 50
5.7.2 No operation (NOP, NOPLF, PAGE n) ...........................................................................................5 - 52
6. BASIC INSTRUCTIONS 6 - 1 to 6 - 133
6.1 Comparison Operation Instruction.........................................................................................................6 - 2
6.1.1 BIN 16-bit data comparisons (=, < >, >, <=, <, >=) ......................................................................... 6 - 2
6.1.2 BIN 32-bit data comparisons (D=, D< >, D>, D<=,D<, D>=) .......................................................... 6 - 4
6.1.3 Floating decimal point data comparisons (E=, E< >, E>, E<=, E<, E>=) ....................................... 6 - 6
6.1.4 Character string data comparisons ($=, $< >, $>, $<=, $<, $>=)................................................... 6 - 8
6.1.5 BIN block data comparisons (BKCMP, BKCMPP) .........................................................................6 - 12
6.2 Arithmetic Operation Instructions...........................................................................................................6 - 16
6.2.1 BIN 16-bit addition and subtraction operations (+, +P, -, -P)..........................................................6 - 16
6.2.2 BIN 32-bit addition and subtraction operations (D+, D+P, D-, D-P) ...............................................6 - 20
6.2.3 BIN 16-bit multiplication and division operations (
, P, /, /P).......................................................6 - 24
6.2.4 BIN 32-bit multiplication and division operations (D
, D P, D/, D/P) ........................................... 6 - 26
6.2.5 BCD 4-digit addition and subtraction operations (B+, B+P, B-, B-P)..............................................6 - 28
6.2.6 BCD 8-digit addition and subtraction operations (DB+, DB+P, DB-, DB-P)...................................6 - 32
6.2.7 BCD 4-digit multiplication and division operations (B
, B P, B/, B/P)..........................................6 - 36
6.2.8 BCD 8-digit multiplication and division operations (DB
, DB P, DB/, DB/P)...............................6 - 38
6.2.9 Addition and subtraction of floating decimal point data (E+, E+P, E-, E-P).................................... 6 - 40
6.2.10 Multiplication and division of floating decimal point data (E
, E P, E/, E/P)..............................6 - 44
6.2.11 Block addition and subtraction (BK+, BK+P, BK-, BK-P)..............................................................6 - 46
6.2.12 Linking character strings ($+, $+P) ...............................................................................................6 - 49
6.2.13 Incrementing and decrementing 16-bit BIN data (INC, INCP, DEC, DECP) ...............................6 - 53
6.2.14 Incrementing and decrementing 32-bit BIN data (DINC, DINCP, DDEC, DDECP).....................6 - 55
6.3 Data Conversion Instructions.................................................................................................................6 - 57
6.3.1 Conversion from BIN data to 4-digit and 8-digit BCD (BCD, BCDP, DBCD, DBCDP) .................. 6 - 57
6.3.2 Conversion from BCD 4-digit and 8-digit data to BIN data (BIN, BINP, DBIN, DBINP)................. 6 - 59
6.3.3 Conversion from BIN 16 and 32-bit data to floating decimal point (FLT, FLTP, DFLT, DFLTP)... 6 - 61
6.3.4 Conversion from floating decimal point data to BIN 16- and 32-bit data
(INT, INTP, DINT, DINTP) ..............................................................................................................6 - 63
6.3.5 Conversion from BIN 16-bit to BIN 32-bit data (DBL, DBLP) ......................................................... 6 - 65
6.3.6 Conversion from BIN 32-bit to BIN 16-bit data (WORD, WORDP)................................................ 6 - 66
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
To Next Page
Loading...
Need help?
General
