7. STANDARD ADJUSTMENT ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・
19
7-1. Adjustment of the needle bar position ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・
19
7-2. Adjustment of the position between the needle and the shuttle 20
7-3. Adjustment of the clearance between the shuttle hook and the needle ・・・・・・
21
7-4. Adjustment of the clearance between the driver and the 21
7-5. Adjustment of the thread guide ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・
22
7-6. Adjustment of the presser foot ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・
22
7-6-1. Adjustment of the presser foot position ・・・・・・・・・・・・・・・・・・・・・・・・・・・
22
7-6-2. Adjustment of the presser foot lift during the sewing ・・・・・・・・・・・・・・・・
24
7-6-3. Adjustment of the presser foot timing ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・
25
7-7. Adjustment of the wiper ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・
26
7-8. Adjustment of the bobbin 27
7-9. Adjustment of the work 27
7-10. Adjustment of the trimmer cam follower ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・
28
7-11. Adjustment of the position for movable knife 28
7-12. Adjustment of the fixed knife 29
7-13. Adjustment of the thread take up spring stroke ・・・・・・・・・・・・・・・・・・・・・・・・・
29
7-14. Adjustment of the thread take up spring tension ・・・・・・・・・・・・・・・・・・・・・・・・
29
7-15. Adjustment of the thread tail after the trimming ・・・・・・・・・・・・・・・・・・・・・・・・・
30
7-16. Cancellation of the trimming 30
7-17. Adjustment of the upper thread 30
7-18. Adjustment of the 31
7-19. Adjustment of the mechanical home position ・・・・・・・・・・・・・・・・・・・・・・・・・・・
32
7-19-1. Shifting the mechanical home position X 33
7-19-2. Shifting the mechanical home position Y 33
7-20. Adjustment of the X-Y contact pressure ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・
34
7-21. Adjustment of the X-Y driving gear clearance ・・・・・・・・・・・・・・・・・・・・・・・・・・
34
7-21-1. Adjustment of the X stepping motor 34
7-21-2. Adjustment of the Y stepping motor 35
7-22. Adjustment of the V belt tension ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・
35
8. MAINTENANCE ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・
36
8-1. Cleaning ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・
36
8-2. Disposing of oil waste ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・
36
9. BAD SEWING CONDITION & ITS CAUSE AND
37
APPENDIX ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・
40
Ref.1. Table cut-out for PLK-E0504 machine ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・
41
Ref.2. Table and stand ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・
41
Ref.3. Stand 42