EasyManuals Logo

NEC NP-UM330X User Manual

NEC NP-UM330X
149 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #137 background imageLoading...
Page #137 background image
127
8. Appendix
Common Problems & Solutions
(“Power/Status/LampIndicator”onpage126.)
Problem CheckTheseItems
Does not turn on
or shut down
• Checkthatthepowercordispluggedinandthatthepowerbuttonontheprojectorcabinetortheremotecontrol
is on� ( pages 15, 16)
• Ensurethatthelampcoverisinstalledcorrectly.( page 122)
• Checktoseeiftheprojectorhasoverheated.Ifthereisinsufcientventilationaroundtheprojectororiftheroom
where you are presenting is particularly warm, move the projector to a cooler location�
• Checktoseeifyoucontinuetousetheprojectorforanother100hoursafterthelamphasreachedtheendofits
life� If so, replace the lamp� After replacing the lamp, reset the lamp hours used� ( page 120)
• Thelampmayfailtolight.Waitafullminuteandthenturnonthepoweragain.
• Set[FANMODE]to[HIGHALTITUDE]whenusingtheprojectorataltitudesapproximately5500feet/1700meters
or higherUsing the projector at altitudes approximately 5500 feet/1700 meters or higher without setting to [HIGH
ALTITUDE] can cause the projector to overheat and the projector could shut down� If this happens, wait a couple
minutes and turn on the projector� ( page 92)
If you turn on the projector immediately after the lamp is turned off, the fans run without displaying an image for
some time and then the projector will display the image� Wait for a moment�
Will turn off • Ensurethatthe[OFFTIMER]or[AUTOPOWEROFF]isoff.( page 88, 95)
No picture
• UsetheCOMPUTER,theHDMI,theVIDEOortheS-VIDEObuttonontheremotecontroltoselectyoursource
(Computer, HDMI1, HDMI2, Video or S-Video)� ( page 18) If there is still no picture, press the button again�
• Ensureyourcablesareconnectedproperly.
• Usemenustoadjustthebrightnessandcontrast.( page 81)
• Resetthesettingsoradjustmentstofactorypresetlevelsusingthe[RESET]intheMenu.( page 102)
• EnteryourregisteredkeywordiftheSecurityfunctionisenabled.( page 31)
• BesuretoconnecttheprojectorandnotebookPCwhiletheprojectorisinstandbymodeandbeforeturningon
the power to the notebook PC�
In most cases the output signal from the notebook PC is not turned on unless connected to the projector before
being powered up�
* If the screen goes blank while using your remote control, it may be the result of the computer’s screen-saver
or power management software�
• Seealsothenext page
Picture suddenly be-
comes dark
• CheckiftheprojectorisintheForcedECOmodebecauseoftoohighambienttemperature.Ifthisisthecase,
lower the internal temperature of the projector by selecting [HIGH] for [FAN MODE]� ( page 92)
Color tone or hue is un-
usual
• Checkifanappropriatecolorisselectedin[WALLCOLOR].Ifso,selectanappropriateoption.( page 87)
• Adjust[HUE]in[PICTURE].( page 81)
Image isn’t square to the
screen
• Repositiontheprojectortoimproveitsangletothescreen.( page 20, 21)
• UsetheKeystonecorrectionfunctiontocorrectthetrapezoiddistortion.( page 23)
Picture is blurred
• Adjustthefocus.( page 20)
• Repositiontheprojectortoimproveitsangletothescreen.( page 20, 21)
• Ensurethatthedistancebetweentheprojectorandscreeniswithintheadjustmentrangeoftheprojectionwindow.
( page 103, 104)
• Condensationmayformonthelensiftheprojectoriscold,broughtintoawarmplaceandisthenturnedon.
Should this happen, let the projector stand until there is no condensation on the lens�
Flic k e r appe a r s on
screen
•
Set [FAN MODE] to other than [HIGH ALTITUDE] mode when using the projector at altitudes approximately 5500 feet/1700
meters or lower� Using the projector at altitudes less than approximately 5500 feet/1700 meters and setting to [HIGH ALTI-
TUDE] can cause the lamp to overcool, causing the image to flicker� Switch [FAN MODE] to [AUTO]� ( page 92)
Image is scrolling ver-
tically, horizontally or
both
• Checkthecomputer’sresolutionandfrequency.Makesurethattheresolutionyouaretryingtodisplayissupported
by the projector� ( page 133)
• AdjustthecomputerimagemanuallywiththeHorizontal/Verticalinthe[IMAGEOPTIONS].( page 83)
Remote control does
not work
• Installnewbatteries.( page 10)
• Makesuretherearenoobstaclesbetweenyouandtheprojector.
• Standwithin22feet(7m)oftheprojector.( page 10)
Indicator is lit or blink-
ing
• SeethePOWER/STATUS/LAMPIndicator.( page 126)
Cross color in RGB
mode
• PresstheAUTOADJ.buttonontheprojectorcabinetortheremotecontrol.( page 25)
• Adjustthecomputerimagemanuallywith[CLOCK]/[PHASE]in[IMAGEOPTIONS]inthemenu.( page 82)

Table of Contents

Other manuals for NEC NP-UM330X

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the NEC NP-UM330X and is the answer not in the manual?

NEC NP-UM330X Specifications

General IconGeneral
BrandNEC
ModelNP-UM330X
CategoryProjector
LanguageEnglish

Related product manuals