Nortek Linear eMerge e3 Series - 2.0 Control Panel Layout; 2.1 Control Panel Components

www.linearcorp.com 4 e3 eMerge Installation Instructions
2.0 Control Panel Layout
2.1 Control Panel Components
 e following illustration shows the e3 control panel wiring and components.
Note: Wiring methods
shall be in accordance
with the National
Electrical Code/NPFA 70
and all local codes.
Note: The terminals
are designed to accept
12-22 AWG, solid or
stranded wire.
Note: To factory default
the system, press &
hold S1 for 20 seconds.
When released, the
system will start the
factory default process.
It is VERY important to
wait 2-3 minutes for a
solid blue LED (DL1)
before programming the
system. All user data will
be erased, including the
license key.
AUX RELAY 1
AUX RELAY 2
AUX RELAY 3
AUX RELAY 4
-
TAMPER
OUT READER
NC
C
NO
NC
C
NO
NC
C
NO
NC
C
NO
DOOR 1
DOOR 2
DOOR 3
DOOR 4
ETHERNET
TMP -
TMP +
FLT -
FLT +
-
+
PWR FAULT
Micro SD
SLOT
RESET
LED BANK
LAN LED
DL8
DL7
DL6
DL5
DL4
DL3
DL2
DL1
DL17
DL16
DL15
DL14
DL13
DL12
DL11
DL10
DL9
DL19
DL18
JP1
S2
S1
External
+12VDC
POE
(Default)
JP1 - Power Input
EARTH
GROUND &
READER
SHIELD LEAD
D0 IN D1 IN D0 OUT D1 OUT
2
1
3
4
D9
S2: Hardware reset
S1: Factory default
+
12VDC
INPUT GND INPUT
12V
AUX IN GND AUX IN
INPUT GND INPUT
D0 IN D1 IN D0 OUT D1 OUT
12V
REX GND DOOR CONTACT
AUX INPUT 4 GND AUX INPUT 3
IN READER
REX GND DOOR CONTACT
OUT READER
IN READER
NC
C
NO
NC
C
NO
NC
C
NO
NC
C
NO
DOOR 2 LOCK
DOOR 1 LOCK
DOOR 3 LOCK
DOOR 4 LOCK
OUT READER
D0 IN D1 IN D0 OUT D1 OUT
INPUT GND INPUT
12V
AUX IN GND AUX IN
INPUT GND INPUT
D0 IN D1 IN D0 OUT D1 OUT
12V
REX GND DOOR CONTACT
AUX INPUT 2 GND AUX INPUT 1
IN READER
REX GND DOOR CONTACT
OUT READER
IN READER
-
+
-
+
+
-
+
-
Figure 2.1. Board Layout
Table 2.1: LED Indicators
Table 2.2: Default I/O States
LED Condition
➀ DL17
Red On = Power On Middle Board
➁ D9
Red On = Power On Bottom Board
➂ DL1
Blue On = System is Rebooted
DL1 to DL16 Blue On = System is Booting
➃ DL19, DL18
Blue Blink = Network Connection
NOTE: System start up time is approx. 60 secs.
Attribute Default State
Door Status Inputs
Normally Open, Unsupervised, 8 Sec. Held Open Time
REX Inputs Normally Open, Momentary, Unsupervised
Auxiliary Inputs Normally Open, Unsupervised
Door Lock Outputs Not Energized, Single Pulse, 3 Second Unlock Time
Aux Outputs Not Energized, Single Pulse, 3 Seconds On
Note: For UL installations, the maximum Ethernet cable length is 30m (98.5 FT).