Oki C834DN - Using Ethertalk

- 40 -
Connecting to a Computer
1
1. Setup
 Using EtherTalk
(For Mac OS X 10.3.9 to 10.4.11)
When connecting to the network with EtherTalk,
it is necessary to enable EtherTalk and disable
the sleep mode on the printer. After doing that,
install the driver on the computer.
Memo
● The following procedure uses Mac OS X 10.4.11 as an
example. Depending on an OS, the description may be
different.
 First, enable EtherTalk and disable the
sleep mode on the printer.
1 Ensure that your printer and the
computer are turned on and connected.
Reference
● “Connecting an Ethernet Cable” P.31
2 Press the <ENTER> button on the
operator panel.
3 Press the scroll button several times
to select [Admin Setup], and press the
<ENTER> button.
䎩䏘䏑䏆䏗䏌䏒䏑䏖䎃䎃䎃䎃䎃䎃䎕䎒䎕
䫹 䎦䏄䏏䏌䏅䏕䏄䏗䏌䏒䏑
䎤䏇䏐䏌䏑䎃䎶䏈䏗䏘䏓
4 Enter the administrator password, using
the numeric (0-9) keys.
The factory default password is “aaaaaa” Press
the <ENTER> button after each character you
input.
䎨䏑䏗䏈䏕䎃䎳䏄䏖䏖䏚䏒䏕䏇
䯴䎙䎐䎔䎕䏇䏌䏊䏌䏗䏖䎌
5 Press the <ENTER> button.
6 Check that [Network Setup] is selected
and press the <ENTER> button.
䎤䏇䏐䏌䏑䎃䎶䏈䏗䏘䏓䎃 䎃 䎃䎃䎔䎒䎗
䎳䏕䏌䏑䏗䎃 䎶䏈䏗䏘䏓
䎳䎶䎃䎶䏈䏗䏘䏓
䎳䎦䎯䎃䎶䏈䏗䏘䏓
䎱䏈䏗䏚䏒䏕䏎䎃䎶䏈䏗䏘䏓
7 Press the scroll button several times
to select [EtherTalk], and press the
<ENTER> button.
䎱䏈䏗䏚䏒䏕䏎䎃䎶䏈䏗䏘䏓䎃䎃䎕䎒䎘
䎨䏗䏋䏈䏕䎷䏄䏏䏎
䎬䎳䏙䎗䎃 䎤䏇䏇䏕䏈䏖䏖
䎶䏘䏅䏑䏈䏗䎃䎰䏄䏖䏎
䎬䎳䎃䎤䏇䏇䏕䏈䏖䏖䎃䎶䏈䏗
8 Press the scroll button to select
[Enable], and press the <ENTER>
button.
䎨䏗䏋䏈䏕䎷䏄䏏䏎䎃䎃䎃䎃䎃䎃䎃䎔䎒䎔
䎧䏌䏖䏄䏅䏏䏈
䎍䎃 䎃 䎨䏑䏄䏅䏏䏈
9 Press the <BACK> button until
[Network Setup] is displayed.
䎱䏈䏗䏚䏒䏕䏎䎃䎶䏈䏗䏘䏓䎃䎃䎕䎒䎘
䎨䏗䏋䏈䏕䎷䏄䏏䏎
䎬䎳䏙䎗䎃 䎤䏇䏇䏕䏈䏖䏖
䎶䏘䏅䏑䏈䏗䎃䎰䏄䏖䏎
䎬䎳䎃䎤䏇䏇䏕䏈䏖䏖䎃䎶䏈䏗