Oki C834DN - Printing in Custom Sizes

- 69 -
Convenient Print Functions
2
2. Printing Basic Operation
 Printing in Custom Sizes
To load custom size paper, you need to register
the width and length of the paper before
printing. The range of the sizes you can set
differs according to the paper tray.
Tray Available size range
Tray1 Width:
105 to 297 mm (4.1 to 11.7 inches)
Length:
148, 182 to 431.8 mm
(5.8, 7.2 to 17.0 inches)
Tray 2/3/4
(Option)
Width:
148 to 297 mm (5.8 to 11.7 inches)
Length:
182 to 431.8 mm (7.2 to 17.0 inches)
MP tray Width:
64 to 297 mm (2.5 to 11.7 inches)
Length:
90 to 1321 mm (3.5 to 52 inches)
Note
● [Custom] is displayed only when [Paper Size] is set to
[Custom].
● The available size range for duplex printing is the same as
that for tray 2/3/4.
1 Press the <ENTER> button on the
operator panel.
2 Press the scroll button several times
to select [Menus] and press the
<ENTER> button.
䎩䏘䏑䏆䏗䏌䏒䏑䏖䎃䎃䎃䎃䎃䎃䎔䎒䎕
䎳䏕䏌䏑䏗䎃䎬䏑䏉䏒䏕䏐䏄䏗䏌䏒䏑
䎳䏕䏌䏑䏗䎃䎶䏈䏆䏘䏕䏈䎃䎭䏒䏅
䎰䏈䏑䏘䏖
䎦䏒䏑䏉䏌䏊䏘䏕䏄䏗䏌䏒䏑
3 Check that [Tray Conguration]
is selected and press the <ENTER>
button.
䎰䏈䏑䏘䏖 䎃䎃䎃䎃䎃䎃䎃䫹䎔䎒䎔
䎶䏜䏖䏗䏈䏐䎃䎤䏇䏍䏘䏖䏗
䎷䏕䏄䏜䎃䎦䏒䏑䏉䏌䏊䏘䏕䏄䏗䏌䏒䏑
4 Press the scroll button several times
to select [Tray Cong] of the paper
tray in which you loaded paper and then
press the <ENTER> button.
䎷䏕䏄䏜䎃 䎦䏒䏑䏉䏌䏊䏘䏕䏄䏗䏌䏒䏑 䎔䎒䎖
䎷䏕䏄䏜䎔 䎃䎦䏒䏑䏉䏌䏊
䎰䎳 䎷䏕䏄䏜 䎃 䎦䏒䏑䏉䏌䏊
䎷䏕䏄䏜䎖 䎃䎦䏒䏑䏉䏌䏊
䎷䏕䏄䏜䎕 䎃䎦䏒䏑䏉䏌䏊
5 Check that [Paper Size] is selected and
press the <ENTER> button.
䎰䎳䎷䏕䏄䏜䎃 䎦䏒䏑䏉䏌䏊 䎃䎃䎃䎔䎒䎔
䎳䏄䏓䏈䏕䎃 䎶䏌䏝䏈
䎰䏈䏇䏌䏄䎃 䎷䏜䏓䏈
䎰䏈䏇䏌䏄 䎃䎺䏈䏌䏊䏋䏗
䎷䏕䏄䏜䎃 䎸䏖䏄䏊䏈
6 Press the scroll button several times
to select [Custom] and then press the
<ENTER> button.
䎳䏄䏓䏈䏕䎃䎶䏌䏝䏈
䎃䎃䫹
䎚䎒䎔䎔
䎍䎃䎦䏘䏖䏗䏒䏐
䎦䏒䏐䎐䎔䎓䎃䎨䏑䏙䏈䏏䏒䏓䏈
䎦䎘
䎧䎯䎃䎨䏑䏙䏈䏏䏒䏓䏈
7 Press the <BACK> button.