Omega CN16Pt - Page 2

To Next Page

To Previous Page

PLATINUM

Series User’s Guide

Introduction

The information contained in this document is believed to be correct, but OMEGA accepts no liability for any errors it contains, and

reserves the right to alter specifications without notice.

Omega Engineering | www.omega.com

Main Page

Table of Contents3
Introduction7
Description7
Using this Manual8
Safety Considerations9
Wiring Instructions10
1.4.1 Back Panel Connections10
1.4.2 Connecting Power11
1.4.3 Connecting Inputs11
1.4.4 Connecting Outputs13
PLATINUM TM Series Navigation14
Description of Button Actions14
Menu Structure14
Level 1 Menu14
Circular Flow of Menus15
Complete Menu Structure15
Initialization Mode Menu (Init)15
Programming Mode Menu (Prog)19
Operating Mode Menu (Oper)21
Reference Section: Initialization Mode (Init)22
Input Configuration (Init > Inpt)22
Thermocouple Input Type (Init > Inpt > T.C.)22
Resistance Temperature Detector (RTD) Input Type (Init > Inpt > Rtd)23
Thermistor Input Type Configuration (Init > Inpt > Thrm)24
Process Input Type Configuration (Init > Inpt > Proc)24
Display Reading Formats (Init > Rdg)25
Decimal Point Format (Init > Rdg > Dec.p)25
Temperature Units (Init > Rdg > °F°C)25
Filter (Init > Rdg > Fltr)26
Annunciator Settings (Init > Rdg > ANN.1/ANN.2)26
Normal Color (Init > Rdg > NCLR)27
Brightness (Init > Rdg > Brgt)27
Excitation Voltage (Init > Ectn)27
Communication (Init > Comm)28
Protocol (Init > Comm > Usb, Ethn, SER > Prot)28
Address (Init > Comm > Usb, Ethn, SER > Addr)29
Serial Communications Parameters (Init > Comm > SER >C.PAR)29
Safety Features (Init > Sfty)31
Power on Confirmation (Init > Sfty > Pwon)31
Operating Mode Confirmation (Init > Sfty > Oper)31
Setpoint Limits (Init > Sfty > SP.LM)31
Loop Break Timeout (Init > Sfty > Lpbk)32
Open Circuit (Init > Sfty > O.crk)32
Manual Temperature Calibration (Init > T.cal)32
No Manual Temperature Calibration Adjustment (Init > T.cal > None)33
Manual Temperature Calibration Offset Adjustment (Init > T.cal > 1.Pnt)33
Manual Temperature Calibration Offset and Slope Adjustment (Init > T.cal > 2.Pnt)33
Temperature Ice Point Calibration (Init > T.cal > ICE.P)33
Save Current Configuration for All Parameters to a File (Init > SAVE)33
Load a Configuration for All Parameters from a File (Init > Load)34
Display Firmware Revision Number (Init > VER.N)34
Update Firmware Revision (Init > VER.U)34
Reset to Factory Default Parameters (Init > F.dft)34
Password-Protect Initialization Mode Access (Init > I.pwd)34
Password-Protect Programming Mode Access (Init34
Reference Section: Programming Mode (Prog)35
Setpoint 1 Configuration (Prog > SP1)35
Setpoint 2 Configuration (Prog > SP2)35
Alarm Mode Configuration (Prog > ALM.1, ALM.2)36
Alarm Type (Prog > ALM.1, ALM.2 > Type)36
Absolute or Deviation Alarm (Prog > ALM.1, ALM.2 > Type > Ab.DV)37
Alarm High Reference (Prog > ALM.1, ALM.2 > Type > ALR.H)37
Alarm Low Reference (Prog > ALM.1, ALM.2 > Type > ALR.L)37
Alarm Color (Prog > ALM.1, ALM.2 > A.CLR)38
Alarm High High / Low Low Offset Value (Prog > ALM.1, ALM.2 > HI.HI)38
Alarm Latching (Prog > ALM.1, ALM.2 > Ltch)38
Alarm Normally Closed, Normally Open (Prog > ALM.1, ALM.2 > Ctcl)39
Alarm Power-On Behavior (Prog > ALM.1, ALM.2 > a39
Alarm on Delay (Prog > ALM.1, ALM.2 > De.on)39
Alarm off Delay (Prog > ALM.1, ALM.2 > De.of)39
Output Channel 1-3 Configuration (Prog > Out.1-Out.3)40
Output Channel Mode (Prog > Out1-Out3 > Mode)40
Output Channel 1-4 Configuration (Prog > Out.1-Out.4)40
Output Cycle Pulse Width (Prog > Out1-Out3 > Cycl)42
Analog Output Range (Prog > Out1-Out3 > RNGE)43
PID Configuration (Prog > Pid.s)43
Action Response (Prog > Pid > Actn)43
PID Configuration (Prog > Pid)43
Autotune Timeout (Prog > Pid > A.to)44
Autotune (Prog > Pid > Auto)44
PID Gain Settings (Prog > Pid > GAIN)44
Low Output Clamping Limit (Prog > Pid > %Lo)45
High Output Clamping Limit (Prog > Pid > %HI)45
Adaptive Tuning (Prog > Pid > Adpt)45
Remote Setpoint Configuration (Prog > RM.SP)46
5.6.1 Cascade Control Using Remote Setpoint47
Multi-Ramp/Soak Mode Parameters (Prog > M.RMP)48
Multi-Ramp/Soak Mode Control (Prog > M.RMP > R.ctl)48
Select Program (Prog > M.RMP > S.PRG)49
Multi-Ramp/Soak Tracking (Prog > M.RMP > M.trk)49
Time Format (Prog > M.RMP > Tim.f)49
Program End Action (Prog > M.RMP > E.ACT)49
Number of Segments (Prog > M.RMP > N.SEG)50
Segment Number for Editing (Prog > M.RMP > S.SEG)50
5.7.8 more on Multi-Ramp/Soak Programming51
Reference Section: Operating Mode (Oper)52
Normal Run Mode (Oper > RUN)52
Change Setpoint 1 (Oper > SP1)53
Change Setpoint 2 (Oper > SP2)53
Manual Mode (Oper > MANL)53
Pause Mode (Oper > PAUS)53
Stop Process (Oper > Stop)54
Clear Latched Alarms (Oper > L.rst)54
Display Valley Reading (Oper > Valy)54
Display Peak Reading (Oper > Peak)54
Standby Mode (Oper > Stby)54
Specifications55
Inputs55
Control55
Outputs56
Communications (USB Standard, Optional Serial and Ethernet)56
Isolation56
General56
Approvals Information59

Omega CN16Pt - Page 2

Table of Contents

Related product manuals