Omron E5AN-H User Manual

339
Appendix
25.0
c
al1l
0.0
c
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
25.0
c
25.0
0.0
c
a-m
bank
0
rsp
0.0
sp-m
0.0
ct1
0.0
ct2
0.0
lcr1
0.0
lcr2
0.0
prst
rset
sktr
0
r-s
run
al-1
0.0
c
al-2
0.0
c
al2h
0.0
c
al2l
0.0
c
al-3
0.0
c
al3h
0.0
al3l
0.0
o
0.0
c-o
0.0
v-m
0.0
al1h
0.0
c
PF PF
PF
PF
25.0
0.0
c
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
l.adj
at
off
cmwt
off
irda
off
spmd
lsp
ct1
0.0
ins
0.00
c
insh
0.00
c
insl
0.00
c
p
8.0
c
i
233.0
d
40.0
c-sc
1.00
c-db
0.0
of-r
50.0
hys
1.0
chys
1.0
soak
1
wt-b
off
mv-s
0.0
mv-e
0.0
sprt
off
ol-h
105.0
ol-l
-5.0
db
2.0
oc-h
0.8
sqrp
0.0
M
orl
M
0.0
M
M
M
M
M
M
M
M
ct2
0.0
lcr1
0.0
lcr2
0.0
hb1
0.0
hb2
0.0
hs1
50.0
hs2
50.0
oc1
50.0
oc2
50.0
M
100.0
Starting in manual mode.
Note:
Power ON
Starting in
automatic
mode.
Manual Control Level
PID
Control
only
PV/MV
Press the O Key less than 1 s.
Operation Level
Adjustment Level
Adjustment Level
Display
Displayed only
once when
entering
adjustment level.
AT Execute/Cancel
Communications
Writing
Heater Current 1
Value Monitor
Heater Burnout
Detection 1
Heater Overcurrent
Detection 1
Heater Current 2
Value Monitor
Heater Burnout
Detection 2
Heater Overcurrent
Detection 2
Leakage Current 1
Monitor
Leakage Current 2
Monitor
HS Alarm 1
HS Alarm 2
Temperature Input Shift
1-point shift
2-point shift
Upper Limit
Temperature
Input Shift Value
Lower Limit
Temperature
Input Shift Value
Proportional Band
Integral Time
PID settings
Derivative Time
Cooling Coefficient
Heating/cooling
Dead Band
Manual Reset Value
Clear the offset during
stabilization of P or PD
control.
Hysteresis (Heating)
Hysteresis (Cooling)
Hysteresis settings
Soak Time
Wait Band
MV at Stop
MV at PV Error
SP Ramp Set Value
MV Upper Limit
MV Lower Limit
MV Change Rate Limit
Process Value
Added when Additional
PV display is ON.
Process Value/
Set Point
Auto/Manual Switch
PID control only.
Added when auto/man-
ual select addition is ON.
Set Point During
SP Ramp
Heater Current 1 Value
Monitor
Heater Current 2 Value
Monitor
Leakage Current 1
Monitor
Leakage Current 2
Monitor
Program Start
Soak Time Remain
Press the O
and M Keys for
at least 3 s.
RUN/STOP
Alarm Value 1
Set either of these parameters.
Alarm Value
Upper Limit 1
Alarm Value
Lower Limit 1
Alarm Value 2
Set either of these parameters.
Alarm Value
Upper Limit 2
Alarm Value
Lower Limit 2
Alarm Value 3
Alarm Value
Upper Limit 3
Alarm Value
Lower Limit 3
Set either of these parameters.
MV Monitor (Heating)
MV Monitor (Cooling)
Press the PF Key
for at least 1 s.
(See note 1.)
Press the O
Key or the PF
Key for at least
1 s.
(See note 1.).
1. When the PF Setting parameter is set to A-M for a Controller with a PF Key (E5AN/EN-H).
2. When the PF Setting parameter is set to PFDP for a Controller with a PF Key (E5AN/EN-H).
Press
the O
Key for
at least
3 s.
Set either
of these
parame-
ters.
Extraction of Square
Root
Low-cut Point
Press the O
and M Keys for
at least 1 s.
PF Key (See note 2.)
PF Key (See note 2.)
Monitor/Setting Item Level
(E5AN/EN-H only)
Monitor/Setting
Item Display 1
Monitor/Setting
Item Display 2
Monitor/Setting
Item Display 3
Monitor/Setting
Item Display 4
Monitor/Setting
Item Display 5
Note: The monitor/setting items to be displayed is set in the Monitor/Setting Item 1 to
5 parameters (advanced function setting level).
Infrared Communications Use
SP Mode
Position Proportional
Dead Band
Open/Close Hysteresis
Bank No.
Remote SP Monitor
Valve Opening
Monitor

Omron E5AN-H Specifications

General

Brand	Omron
Model	E5AN-H
Category	Temperature Controller
Language	English