Front panel facilities
For further operational instructions, see the pages indicated in
brackets [ I.
POWER switch (for all models other than USA and
Canadian models, and Australian models) [28]
Press to turn on and off the main power supply for the TX-SR701/
701E/601/601E. When the TX-SR7OI/701E/601/601E is turned on
with the POWER swilch, the STANDBY indicator lights.
• Before turning on the power, check to make sure that all coMs
are properly connected.
• When the power is turned on, a sudden surge of current will
occur thai may adversely affect the opera/ion of other devices.
'Ik) prevent this, do not plug the TX-SR701/701E/601/601E into
the same circuit used by sensitive equipment, e.g., computers.
@ STANDBY/ON button [28]
If pressed with the POWER swilch turned on (with the receiver
plugged in for US models and Australian models), the TX-SR701/
701E/601/601E turns on and the display lights up. If pressed again,
the TX-SR701/701E/601/601E returns to the standby state. In the
standby state, the display is turned off and the TX-SR701/701E/
601/601E cannot be operated.
@ STANDBY indicator [7,28]
Lights when the TX-SR701/701E/601/601E is in the standby state
and when a signal is received from the remote controller.
@ DISPLAY button [45]
Press to display infomlation about the cmTent input source signal.
Each thne you press the display button, the screen changes to show
you different information concerning the input signal.
@ RT/PTYFrP (European models only) button [40]
This button is only available on European models. Press this bullon
to tune into the Radio Data Syslem (RDS) for FM broadcasting.
RDS was developed within the European Broadcasting Union
(EBU) and is available in most European countries. Each time the
bullon is pressed, the display changes from RT (radio lext) to PTY
(program type) to TP (traffic program) and then back to El" again.
DIMMER button
(other than European models)
Press to set the brightness of the front display.
There are three settings available: normal, dark,
and very dark.
• The brightness of the front display can also
be adjusted using the remote controller.
®
LISTENING MODE buttons [46-5t]
Press these buttons to select a listening mode for the current input
source. Press the DIRECT (TX-SR601/601E), THX (TX-SR701/
701E), STEREO, and SURROUND buttons to select a listening
mode directly. Press the DSP button to select any of the possible
listening modes for the input source currently selected.
Note:
During playback of a multichalmel source, press the DIRECT
button to turn off the tone control and the SURROUND button to
turn on the tone control. [45]
Front display [11]
@ MEMORY button [38]
Press to assign the radio station that you are currently tuned into to a
preset channel or press to delete a previously preset station.
@ FM MODE button [37]
Press to change the stereo mode fronl AUTO to MONO and vice
versa. Each time this button is pressed, the AUTO indica/ion turns
on and off indicating the current mode. if you are listening to an FM
radio station in stereo and the sound cuts out or there is a great deal
of noise, switch from AUTO to MONO.
(_ Remote control sensor [7]
AUDIO ADJUST button [57]
Press to adjust the sound quality and the listening mode.
SETUP button [31]
Press to enter the Setup Menu. The OSD Menu will appear on the
TV monitor as well as the front display on the TX-SR7OI/701E/
601/601E.
(_ RETURN button [32]
When in the Setup Menu, press to go back one level. If pressed
while at the Main Menu, you will exit the Setup Menu.
(_) TUNING i#•, PRESET _111%cursor (AlVl41i_ ") buttons
[31,37, 38]
To tune into a radio station, press the 'IUNING A/• buttons. The
tuner frequency is displayed in the front display and it can be
changed in 100-kHz (or 50-kHz) increments for FM and 10-kHz (or
9-kHz) increments for AM.
When FM is selected as the input source, you can hold down either
the TUNING • or • bmion and then release it to activate the auto-
seamh feature. It will search for a sta/ion in the direction of the
button you pressed and stop when it tunes into one. When
naviga/ing through the menu settings, these buttons move the cursor
up or down (or change the highlighied item).
To select a radio station thai was stored using the MEMORY button,
press the PRESET _1/_" buttons.
When navigating through the menu settings, these buttons select the
value or item thai you selected with the TUNING •/• buttons.
When you press the SETUP button, the TUNING and PRESET
buttons become cursor buttons to be used for Setup Menu
operations.
(_ ENTER button [31]
Press to display the screen for the item that is selected in the Setup
Menu.
MASTER VOLUME dial [41]
Use to control the volume in the main zone. 'lhe volume for the
remote zone (Zone 2) is independent.
VIDEO 4 INPUT terminals [21]
laor connecting a video camera or game device.
9
To Next Page
Loading...
