Panasonic AJ-PX380G - [RECORDING SETUP]

– 138 –
Chapter 6 Menu Operations — Menu list
[RECORDING SETUP]
These are various types of setting items when performing camera recording and playback.
Select the recording format.
Item Description of settings
[REC MEDIA] Selects the slot for the media to be recorded.
[microP2]: Uses microP2 memory cards (slots 1 and 2).
[P2]: Uses P2 memory card (card slot 3).
f Factory setting: [microP2]
[FILE SPLIT] Selects the split method of the recording le.
[ONE FILE]: The clip is recorded in one le in the AVC-LongG format to a microP2 memory card
(exceeding 32 GB).
[SPLIT]: Divides the le every 4 GB regardless of the recording format.
[SHORT SPLIT]: Divides the le every 128 seconds regardless of the recording format.
f Factory setting: [SPLIT]
If the clip is recorded in one le, it cannot be copied to a P2 memory card or microP2 memory card with a
capacity of 32 GB, or cannot be copied or exported to a storage. If one le exceeds approximately 4 GB, a
clip cannot be transferred to a sever device on the network using the FTP client function.
When [ONE FILE] is selected, proxy recording is not possible. Also, when the main menu → [RECORDING
SETUP] → [DUAL CODEC SETTING] → [CODEC USAGE] is set to [PROXY REC(P2)] or [PROXY
REC(P2&SD)], [ONE FILE] cannot be selected.
It will be divided to recording les of approximately 128 seconds when [SHORT] is selected, but they
can be operated as a single clip when the thumbnail of the clips are operated on the P2 device. A single
continuous recording time is approximately 3.5 hours. [SHORT SPLIT] is disabled in interval recording,
one-shot recording, and loop recording modes.
[RECORDING] Selects the recording format.
[NORMAL]: Performs standard recording.
[INTERVAL]: Performs interval recording.
[ONE SHOT]: Performs one-shot recording.
[LOOP]: Performs loop recording.
f Factory setting: [NORMAL]
[RECORDING
SETTING]
[RECORDING HOLD] Selects whether to hold [RECORDING] settings.
[ON]: Holds the settings.
[OFF]: Does not hold the settings. It will always be [NORMAL] the next time when the power is turned on.
f Factory setting: [OFF]
[ONE SHOT TIME] Sets the recording duration of one-shot recording.
[1frm], [2frm], [4frm], [8frm], [16frm], [1s]
f Factory setting: [1frm]
[INTERVAL TIME] Sets the interval duration for interval recording.
[2frm], [4frm], [8frm], [16frm], [1s], [2s], [5s], [10s], [30s], [1min], [5min], [10min]
f Factory setting: [2frm]
[START DELAY] Selects whether to delay the recording start time by approximately one second when performing interval
recording or one-short recording.
[ON], [OFF]
f Factory setting: [OFF]
[PRE REC] Selects whether to perform pre-recording. If [ON] is selected, pre-recording is performed for approximately
three seconds in HD, and for approximately seven seconds in SD.
[ON], [OFF]
f Factory setting: [OFF]
[ONE CLIP REC] Selects whether to perform one-clip recording.
[ON], [OFF]
f Factory setting: [OFF]
[SIMUL REC] Selects whether to perform simultaneous recording.
[ON], [OFF]
f Factory setting: [OFF]
[DUAL CODEC
SETTING]
[CODEC USAGE] Selects media for recording proxy data.
[PROXY REC(P2)]: Records proxy data to a P2 card.
[PROXY REC(P2&SD)]: Records proxy data to both of a P2 card and SD memory card.
[STREAMING]: Outputs video stream.
[OFF]: Does not record proxy data or output streaming.
f Factory setting: [OFF]
If [CODEC USAGE] cannot be changed, change the [PROXY REC MODE] or [STREAMING MODE]
setting.
[PROXY REC MODE] Sets the recording mode of proxy data.
[LOW 2CH MOV], [HQ 2CH MOV], [SHQ 2CH MOV], [AVC-G6 2CH MOV]
f Factory setting: [HQ 2CH MOV]
[STREAMING MODE] Sets the transfer mode for streaming.
[LOW], [HQ], [AVC-G6], [SHQ (QoS)], [AVC-G (QoS)]
f Factory setting: [HQ]
[PROXY DISP] Selects whether to display proxy data recorded information or messages in the viewnder.
[ON]: Displays proxy recording information and SD memory card remaining capacity at the start of
recording. Warning information is displayed at all times.
[OFF]: Displays proxy and SD memory card warning information for only three seconds when warning
occurs.
f Factory setting: [OFF]