Panasonic AJ-PX380G - [IN;OUT SEL]

– 143 –
Chapter 6 Menu Operations — Menu list
Item Description of settings
[LIMITER CH3] Enables/disables the limiter for audio channel 3.
[ON], [OFF]
f Factory setting: [OFF]
[LIMITER CH4] Enables/disables the limiter for audio channel 4.
[ON], [OFF]
f Factory setting: [OFF]
[HEADROOM] Sets the headroom (standard level).
[18dB], [20dB]
f Factory setting: [20dB]
[OUTPUT SETTING] [TEST TONE] Outputs rated level 1 kHz tone signal according to the reference level.
The standard level varies depending on the setting of [HEADROOM].
[NORMAL]: Outputs the test tone to CH1/CH2/CH3/CH4 when the <OUTPUT>/<AUTO KNEE>
selector switch is switched to <BARS> and audio channel 1 is set to [FRONT] at the [IN] item on the
[AUD02:INPUT] screen of SmartUI.
[ALWAYS]: Always outputs the test tone to CH1/CH2/CH3/CH4 when the <OUTPUT>/<AUTO KNEE>
selector switch is switched to <BARS>.
[CHSEL]: Outputs the test tone to the channel where the [IN] item on the [AUD02:INPUT] screen of
SmartUI is set to [FRONT] when the <OUTPUT>/<AUTO KNEE> selector switch is switched to <BARS>.
(Does not output to CH3/CH4.)
[OFF]: Does not output the test tone.
f Factory setting: [NORMAL]
[IN/OUT SEL]
Performs the setting regarding the input/output of the <SDI OUT1>, <SDI OUT2/IN>, <HDMI>, <GL IN/VIDEO OUT>, and <TC IN/OUT> terminals.
Item Description of settings
[SDI OUT1] Sets video output from the <SDI OUT1> terminal.
[ON]: Outputs video.
[OFF]: Does not output video.
f Factory setting: [ON]
[3G-SDI]
Selects the 1080P signal of the HD SDI output when the main menu → [SYSTEM MODE] →
[LINE&FREQ] is set to [1080-59.94P] or [1080-50P].
[LEVEL-A]: Selects the LEVEL-A method.
[LEVEL-B]: Selects the LEVEL-B DL method.
f Factory setting: [LEVEL-B]
[SDI OUT1 CHAR] Selects whether to superimpose characters on images output from the <SDI OUT1> terminal.
[ON]: Superimposes.
[MON CHAR]: Sets if it will superimpose with the [SETUP] screen → [SET03:MON OUT SETUP] → [CHR]
of SmartUI or the <CHARA> button on the remote control.
[OFF]: Does not superimpose.
f Factory setting: [OFF]
[SDI OUT1 ZEBRA] Selects if the zebra pattern is superimposed to the video signal output from the <SDI OUT1> terminal.
[ON]: Superimposes.
[MON ZEBRA]: Sets if it will superimpose with the [SETUP] screen → [SET03:MON OUT SETUP] →
[ZBR] of the SmartUI or the main menu → [IN/OUT SEL] → [MON OUT ZEBRA].
[OFF]: Does not superimpose.
f Factory setting: [OFF]
[SDI EDH] Selects whether to superimpose EDH when the SDI output is SD signal (480i and 576i).
[ON]: Superimposes.
[OFF]: Does not superimpose.
f Factory setting: [ON]
[HD SDI REMOTE] Sets whether to use the control function of recording operation for an external device (such as a recorder)
connected to the <SDI OUT1> terminal at HD SDI output.
[ON]: Controls the recording operation of the external device.
[OFF]: Does not control the recording operation of the external device.
f Factory setting: [OFF]
[SDI OUT2/IN SEL] Selects if the <SDI OUT2/IN> terminal is to be used as the <SDI OUT2> terminal or to be used as the
<SDI IN> terminal. This can be set when the main menu → [SYSTEM MODE] → [REC SIGNAL] is set to
[CAM].
[SDI OUT2]: Uses as the <SDI OUT2> terminal.
[SDI IN]: Uses as the <SDI IN> terminal.
f Factory setting: [SDI OUT2]
[HDMI OUT SIGNAL] Selects the output video signal from the <HDMI> terminal.
[MON]: Outputs the signal from the monitor output.
[VF]: Outputs the same signal as the one from the viewnder. Video format will be 1080i.
[SDI IN]: Outputs the signal input to the <SDI OUT2/IN> terminal. The video format is 1080i, 720P, 480P,
or 576P, in accordance with the setting in the main menu → [SYSTEM MODE] → [LINE&FREQ].
f Factory setting: [MON]
Audio is not output when it is set to [VF] or [SDI IN].
[GL IN/VIDEO OUT SEL] Selects if the <GL IN/VIDEO OUT> terminal to be used as the genlock input or to be used as the video
output.
[GENLOCK IN]: Uses as the genlock input.
[VIDEO OUT]: Uses as the video output.
f Factory setting: [VIDEO OUT]