– 82 –
Chapter 4 Shooting — Multi formats
Setting Recording setting (setting menu) Recording/operation enabled/disabled
Operation mode [REC SIGNAL] [RECORDING]
Dual codec
recording
Text memo Shot mark
Interval recording [CAM] [INTERVAL] Not available Not available Not available
One-shot recording [CAM] [ONE SHOT] Not available Not available Not available
Loop recording [CAM] [LOOP] Not available Not available Not available
Standard recording [CAM] [NORMAL] Refer to “System modes and recording functions”.
SDI input recording [SDI] Disabled Available* Available Available
* It is not available when [LINE&FREQ] is [480-59.94i] or [576-50i].
Selecting video output
The video output method can be selected.
Video output can be selected, for example, in the setting menus and SmartUI.
The setting of the <SDI OUT2/IN> terminal can be switched using the main menu → [IN/OUT SEL] → [SDI OUT2/IN SEL]. The setting of the <GL IN/
VIDEO OUT> terminal can be switched using the main menu → [IN/OUT SEL] → [GL IN/VIDEO OUT SEL].
Setting item Description of settings
[SDI2]
([SET02:MON OUT SELECT] screen of SmartUI)
Select the SDI output signal format from the <SDI OUT2/IN> terminal.
The output signal format from the <HDMI> terminal is determined linked to this when the main
menu → [IN/OUT SEL] → [HDMI OUT SIGNAL] is set to [MON].
[SETUP] (Main menu → [SYSTEM MODE])
Select the setup level of the signal (composite) to output to the <GL IN/VIDEO OUT> terminal.
f [0%]: 0% setup for both output and recording
f [7.5%A]: 7.5% setup for output only (recording 0%)
The [SETUP] menu setting is valid also at playback.
[D.CON]
([SET02:MON OUT SELECT] screen of SmartUI)
Select the screen type at down-conversion output (composite and SD SDI output) in the HD
mode (1080P, 1080i, 720P).
Selecting video output from each terminal
Describes the status of the video output when [MON] is set in the main menu → [IN/OUT SEL] → [HDMI OUT SIGNAL].
[LINE&FREQ]
Monitor output setting
([SET02:MON OUT SELECT]
screen of SmartUI) *
1
Video output
[SDI2] [HDMI] <SDI OUT1> terminal
<SDI OUT2/IN>
terminal
<HDMI> terminal
<GL IN/VIDEO OUT>
terminal
[1080-59.94P]
[1080i] [1080i]
1080/59.94P*
2
1080/59.94i 1080/59.94i
480/59.94i
[480i] [480P] 480/59.94i 480/59.94P
[1080-59.94i]
[1080i] [1080i]
1080/59.94i
1080/59.94i 1080/59.94i
480/59.94i
[480i] [480P] 480/59.94i 480/59.94P
[1080-23.98PsF]
[1080i] [1080i]
1080/23.98PsF
1080/23.98PsF over
59.94i 2:3
1080/23.98PsF over
59.94i 2:3
480/23.98PsF over
59.94i 2:3
[480i] [480P]
480/23.98PsF over
59.94i 2:3
480/23.98PsF over
59.94i 2:3
[720-59.94P]
[720P] [720P]
720/59.94P
720/59.94P 720/59.94P
480/59.94i
[480i] [480P] 480/59.94i 480/59.94P
[480-59.94i] [480i] [480P] 480/59.94i 480/59.94i 480/59.94P 480/59.94i
[1080-50P]
[1080i] [1080i]
1080/50P*
2
1080/50i 1080/50i
576/50i
[576i] [576P] 576/50i 576/50P
[1080-50i]
[1080i] [1080i]
1080/50i
1080/50i 1080/50i
576/50i
[576i] [576P] 576/50i 576/50P
[720-50P]
[720P] [720P]
720/50P
720/50P 720/50P
576/50i
[576i] [576P] 576/50i 576/50P
[576-50i] [576i] [576P] 576/50i 576/50i 576/50P 576/50i
*1 [SDI2] and [HDMI] are interlocked.
*2 1080/59.94P and 1080/50P can be output from only the <SDI OUT1> terminal.
To Next Page
Loading...
