– 145 –
Chapter 6 Menu Operations — Menu list
Item Description of settings
[PLAYLIST] Sets entering/exiting of the playlist edit mode.
[ON], [OFF]
f Factory setting: [OFF]
[IP REMOTE] [ENABLE]: Enables remote control with IP connection.
[DISABLE]: Disables remote control with IP connection.
f Factory setting: [DISABLE]
[USER ACCOUNT] Sets the user account name.
[ACCOUNT LIST] Displays the currently set user account name. Registering of new accounts, deleting accounts, or changing
password can also be performed.
[FTP CLIENT SERVICE] [SETTING DATA] Sets the source from where client service settings are acquired.
[INTERNAL]: Uses the setting value set on the camera.
[SD CARD]: Uses the setting value of the le inside the SD memory card inserted in the SD card slot.
When this item is set to [SD CARD], insert an SD memory card before turning on the power of the camera.
f Factory setting: [INTERNAL]
f [SERVER URL] Sets the server name or an address to connect to.
f [LOGIN USER] Sets the user ID to connect to.
f [LOGIN PASSWORD] Sets the password to connect to.
The menu setting value is displayed with [*].
f [SSH] Sets when transferring les using SSH.
[ENABLE]: Uses SSH.
[DISABLE]: Does not use SSH.
f Factory setting: [DISABLE]
f [SSH PORT] Sets the network port number when SSH is used. Set the same number as that of the server side.
The menu setting value is displayed with [*].
f Factory setting: [22]
f [LOAD (SD CARD)] Loads the setting value of the client service from the SD memory card.
f [SAVE (SD CARD)] Saves the setting value of the client service onto the SD memory card.
[REC DURING
UPLOAD]
Sets whether to use the rec during upload function.
[ENABLE]: Uses the rec during upload function.
[DISABLE]: Does not use the rec during upload function.
f Factory setting: [DISABLE]
[AUTO COPY] Sets whether to enable the function to register clips recorded using the camera automatically to the upload
list when recording stops, and if enabled, sets the type of target clip.
[REC CLIP(PROXY)]: Upload target is proxy data of recorded clips.
[REC CLIP]: Upload target is recorded clips (main recording data and proxy data).
[DISABLE]: Does not automatically upload recorded clips.
f Factory setting: [DISABLE]
[UPLOAD LIST] Displays the list information of clips to upload.
[SAVE LOG (SD CARD)] Save up to the latest 1000 logs for clip information (month and date, clip number (global clip ID), status)
registered in the upload list to an SD memory card.
[STREAMING SETTING] [START TRIGGER] Sets the method for starting video streaming.
[CAMERA]: Starts/stops streaming from the camera.
[RECEIVER]: Operates the start/stop of the streaming distribution from the terminal on the network using
the P2 Browser or the P2 Streaming Receiver.
f Factory setting: [RECEIVER]
[SETTING DATA] Sets the source from where settings for streaming is acquired when [CAMERA] is selected in [START
TRIGGER].
[INTERNAL]: Uses the setting value set on the camera.
[SD CARD]: Uses the setting value of the le inside the SD memory card inserted in the SD card slot.
When this item is set to [SD CARD], insert an SD memory card before turning on the power of the
camera.
f Factory setting: [INTERNAL]
[SERVER ADDR.] Sets the IP address of the device receiving the streaming video when [CAMERA] is selected in [START
TRIGGER].
[RTSP PORT] Sets the RTSP port number required for streaming when [CAMERA] is selected in [START TRIGGER].
f Factory setting: [554]
[LOAD (SD CARD)] When [CAMERA] is selected in [START TRIGGER] and [INTERNAL] is selected in [SETTING DATA], the
connection information necessary for streaming distribution is loaded from the SD memory card.
[SAVE (SD CARD)] When [CAMERA] is selected in [START TRIGGER] and [INTERNAL] is selected in [SETTING DATA], the
connection information necessary for streaming distribution is saved to the SD memory card.
[START] When [CAMERA] is selected in [START TRIGGER], the streaming distribution is started/stopped from the
camera.
[ON]: Starts streaming.
[OFF]: Stops streaming.
[LAN PROPERTY] [MAC ADDRESS] Displays the MAC address of the <LAN> terminal on the camera. (Cannot be changed.)
[DHCP] Sets whether to use automatic acquisition via DHCP. (Mutually exclusive with [DHCP SERVER] setting)
[ENABLE]: Uses automatic acquisition.
[DISABLE]: Does not use automatic acquisition. Set [IP ADDRESS], [SUBNET MASK], [DEFAULT
GATEWAY], [PRIMARY DNS], and [SECONDARY DNS].
f Factory setting: [ENABLE]
[IP ADDRESS] Sets the IP address when [DISABLE] is selected in [DHCP].
f Factory setting: [192.168.0.1]
To Next Page
Loading...
