28
RQT8858
Timer recording
See also “Important notes for recording” (➡ 7).
Depending on the type of disc used for recording or the type of
broadcast, there may be restrictions on the title you are trying to
record.
[RAM] [-R] [-R]DL] [-RW‹V›] [+R] [+R]DL] [+RW] [VHS]
≥You can enter up to 16 programmes up to a month in advance.
(Each daily or weekly programme is counted as one programme.)
[RAM] [-RW‹V›] [+R] [+R]DL] [+RW]
≥To use a new disc, formatting is necessary.
Preparation
≥Turn on the television and select the appropriate video input to suit
the connections to this unit.
≥Insert a disc or video cassette with enough remaining blank space
(➡ 12).
≥Make sure that the clock settings are correct (➡ 70).
Entering G-
CODE numbers is an easy way of timer recording. You can
find these numbers in TV listings in newspapers and magazines.
[Note]
The G-
CODE system is not supported for digital broadcasts.
1 Press [G-Code].
2 Press the numbered buttons to enter
the G-
CODE number.
Press [2] to move back to correct a digit.
3 Press [OK].
≥Confirm the programme (start and end time) by using a TV
magazine, etc. and make corrections if necessary using
[3, 4, 2, 1] (➡ 29, step 3).
≥When “-- ---” appears in the “Name” column, you cannot set
timer recording. Press [3, 4] to select desired programme
position. After you have entered the information of a TV
station, it is kept in the unit’s memory.
4 Press [OK].
The timer programme is stored and the timer icon is
displayed.
“F” lights on the unit’s display to indicate timer recording
standby has been activated.
Repeat steps 1–4 to programme other recordings.
Press [Í DVD/VHS] to turn the unit off.
∫ To cancel recording when recording has already
begun (➡ 30)
∫ To release the unit from recording standby
(➡ 30)
∫ Notes on timer recording (➡ 30)
STATUS
REC MODE
REC
MANUAL SKIP
CREATE
CHAPTER
F
U
N
C
T
I
O
N
M
E
N
U
D
I
R
E
C
T
N
A
V
I
G
A
T
O
R
G
U
I
D
E
RETURN
PAU SE
STOP
SLOW/SEARCH
CH
SELECT
INPUT
0
9
8
7
6
54
3
2
1
CH
AV
¦
TV
DRIVE
SELECT
¦
VOL
DELETE
EXIT
OK
OPTION
ANALOGUE
CH
G-Code
AUDIO
DISPLAY
TIME SLIP
PROG/CHECK
REW
FF
JET REW
G-Code
,,,
OK
DRIVE
SELECT
REC MODE
¦DVD/VHS
PROG/CHECK
Numbered
buttons
“Blue”
Using G-CODE
®
system to make timer
recordings
G-Code
Record
Remain
12:53:00 15. 7. TUE
Input G-Code Number 0-9, and press OK.
1:58 SP
DVD
--:----
VHS
G-Code
Record
Remain
12:53:00 15. 7. TUE
Input G-Code Number 0-9, and press OK.
1:58 SP
DVD
--:----
VHS
Timer
Recording
Remain
12:54:00 15. 7. TUE
Mode
StopStartName Date
Drive
20:0019:0015. 7. TUE SPDVD
2A ARD
Programme Name
All Services : ARD
1:58 SP
DVD
--:----
VHS
No.
Name
ARD
01
&
Timer icon
12:56:00 15. 7. TUE
Mode
Stop
Drive
DVD
Drive
space
SP
OK
20:00
Programme
Check to make sure “OK”
is displayed (➡ 31).
EZ47VGN.book 28 ページ ２００７年６月１８日 月曜日 午後２時１２分
To Next Page
Loading...
