Panasonic DMR-EZ47V

65
RQT8858
§
Depending on the connected equipment, some items may be shaded in grey on the display and cannot be selected, or you may not be able to
change the settings.
(continued on the next page)
Tabs Menus Options (Underlined items are the factory presets.)
Display
On-Screen Messages
Choose the approximate time until the digital channel information
screen (➡ 21) disappears automatically.
The length of time the control panel (➡ 17) is displayed can also
be changed, but “Off” does not work.
≥Off: The digital channel information is not displayed.
≥3 sec. ≥5 sec.
≥7 sec. ≥10 sec.
Grey Background
Select “Off” if you do not want to have the unit show the grey
background when tuner reception is weak.
≥On
≥Off
FL Display
Changes the brightness of the unit’s display.
This setting is fixed with “Automatic” if you set “Power Save”
(➡ 66) to “On”.
≥Bright
≥Dim
≥Automatic: The display turns dark during play and disappears
when the unit is turned off. It reappears momentarily
if a button is pressed. While using this mode, the
standby power consumption can be reduced.
New Service Message (➡ 21)
When a new DVB channel is added this unit will be informed
automatically. Then the confirmation message appears. If you
select “Yes” on the display, Auto-Setup starts (all channel
settings and all created categories are deleted. The timer
recording programmes are also cancelled.).
≥Automatic
≥Off: The service messages are not shown.
Connection
TV Aspect (➡ 18) Set to match the type of
television connected.
≥16:9: When connected to a 16:9 widescreen television.
≥Pan & Scan:
When connected to a 4:3 aspect television, side
picture is trimmed for 16:9 picture (➡ 81).
≥Letterbox:
When connected to a 4:3 aspect television.
16:9 picture is shown in the letterbox style (➡ 81).
Progressive (➡ 19) ≥On ≥Off
TV System (➡ 69) ≥PA L ≥NTSC
HDMI Settings
§
≥Press [OK] to show the following settings.
HDMI Video Format
You can only select items compatible with the connected
equipment. This setting normally does not need to be
changed. However if you are concerned about output picture
quality, it may be improved by changing the setting.
≥576i/480i ≥576p/480p
≥720p ≥1080i
≥1080p: When setting video output to “1080p”, we
recommend using a Panasonic HDMI cable 5
meters or less in length to prevent video distortion.
To enjoy High Quality Video up-converted to 1080p,
you need to connect the unit to 1080p compatible
HDTV.
≥Automatic
: Automatically selects the output resolution best
suited to the connected television (1080p, 1080i,
720p, 576p/480p or 576i/480i).
Aspect for 4:3 Video
To play a 4:3 title when connected with an HDMI cable, set
how to show pictures on a 16:9 widescreen television.
≥4:3
: Picture output expands left or right.
≥16:9: Picture is output as original aspect with
side panels.
Digital Audio Output ≥HDMI and Optical
≥Optical Only: Select when this unit is connected to an amplifier
with an optical digital audio cable and connected
to a TV with an HDMI cable and you want to enjoy
the highest quality of audio from discs (➡ 14).
VIERA Link
Set to use “HDAVI Control” function when connected with an
HDMI cable to a device that supports “HDAVI Control”.
≥On
≥Off: Select when you do not want to use “HDAVI Control”.
VHS Tape Length
Set the length of the tape you are using so the unit can show the
correct remaining time.
≥Auto (E-240)
: The VHS automatically distinguishes E30, -60,
-90, -120, -180, and -240 tapes.
≥E-195: For E195 tape
≥E-260: For E260 tape
≥E-300: For E300 tape
SQPB
To play back video cassettes recorded in S-VHS format (SQPB;
S-VHS Quasi Playback)
≥Automatic
: This unit automatically detects the format in
which the recording was made and selects the
same format for playback. However, picture
distortion may appear.
Therefore, set to “On” or “Off”.
≥On: Use this setting when playing back a cassette
tape recorded in the S-VHS format.
≥Off: Use this setting when playing back a cassette
tape recorded in the VHS format only.
Changing the unit’s settings
EZ47VGN.book 65 ページ ２００７年６月１８日 月曜日 午後２時１２分