Panasonic DMR-EZ47V

76
RQT8858
Troubleshooting guide
Operation Page
VHS Picture
VHS Sound
VHS Recording, Timer Recording
VHS Play
Cannot operate the television.
The remote control doesn’t work.
≥Change the manufacturer code. Some televisions cannot be operated even if you change the
code.
≥The remote control and main unit are using different codes. Change the code on the remote
control.
Press and hold [OK] and the indicated number button at the same time
for more than 5 seconds.
≥The batteries are depleted. Replace them with new ones.
≥You are not pointing the remote control at the main unit’s remote control signal sensor during
operation.
≥Coloured glass may obstruct the signal reception/transmission.
≥Don’t place the signal sensor in direct sunlight or in areas that may be subject to sunlight
exposure.
≥It may be necessary to set the code on the remote control again after changing the batteries.
≥It may be necessary to set the manufacturer code again after changing the batteries.
≥The child lock function is activated.
19
20
9
—
—
—
19, 20
19
61
Cannot operate the DVD. ≥Press [DRIVE SELECT] to select the DVD drive when operating DVDs or CDs. 32
Cannot operate the VHS. ≥Press [DRIVE SELECT] to select the VHS drive when operating video cassettes. 40
The unit is on but cannot be
operated.
≥Recording drive or playback drive has not been selected properly.
≥Some operations may be prohibited by the disc.
≥The unit is hot (“U59” appears on the display). Wait for “U59” to disappear.
≥One of the unit’s safety devices may have been activated.
Reset the unit as follows:
1 Press [Í/I] on the main unit to switch the unit to standby.
If the unit doesn’t switch to standby, press and hold [Í/I] on the main unit for about 10
seconds. The unit is forcibly switched to standby.
Alternatively, disconnect the AC mains lead, wait one minute, then reconnect it.
2 Press [Í/I] on the main unit to switch it on. If the unit still cannot be operated, consult the
dealer.
22, 32
—
—
—
Cannot eject disc. ≥The unit is recording.
≥The unit may have a problem. While the unit is off, press and hold [∫] and [CH W] on the main
unit at the same time for about 5 seconds. Remove the disc and consult the dealer.
If the Child Lock function is activated, above operation does not work. Cancel the Child Lock
function.
—
61
Cannot tune channels. ≥Check the connections. 13
Startup is slow. ≥Make sure that “Quick Start” is set to “On”.
≥Startup takes time in the following situations:
–A disc other than a DVD-RAM is inserted.
–The clock is not set.
–Immediately after a power failure or the AC mains lead is connected.
–When the unit is connected with an HDMI cable.
66
—
On-screen display indicators do
not appear.
≥Select a setting other than “Off” in “On-Screen Messages” in the Setup Menu.
–Press [STATUS ] to show the on-screen display indicators.
41, 65
The grey background appears
during play.
≥You are playing a blank or poor quality part of the video cassette.
≥You can damage the unit if you play dirty or damaged video cassettes and this can cause the
grey background to appear. Consult your dealer.
—
—
Cannot hear the desired audio
type.
≥Press [AUDIO] to select the audio. 41
There is noise when playing a
video cassette.
≥Adjust the tracking.
≥The tape is old or damaged.
41
—
“1” flashes when I try to start
recording.
Cannot record.
≥A video cassette is not inserted. Insert a video cassette with an intact accidental erasure
prevention tab.
≥The erasure prevention tab has been removed. Cover the hole with adhesive tape.
12
12
Cannot record TV programme. ≥The desired channel is not selected. Select the desired TV programme. —
Playback does not work properly. ≥The video head is dirty.
≥The tape is too old or damaged.
≥Check the “SQPB” setting.
≥The video heads are clogged or worn: consult your dealer.
8
—
65
—
EZ47VGN.book 76 ページ ２００７年６月１８日 月曜日 午後２時１２分