Panasonic EBL128

To Next Page

Planning Instructions

MEW01622

Revision -

Fire Alarm System EBL128

V2.0.x

Author: Jan Pettersson

Date of issue: 2013-10-08

Date of rev:

Main Page

Default Chapter3
- Table of Contents3
1 Introduction10
2 Definitions / Explanations12
- Pesn Ab12
- Alarm Point12
- Output Unit13
- Output / Control Output13
- Short Circuit Isolator13
- Display Unit (D.U.)13
- COM Loop13
- Control Unit (C.U.) / C.I.E13
- Fire Brigade Panel (FBP)13
- Control Panel (CP)14
- Led14
- External Indicator (LED)14
- Display / LCD14
- Door Open / Key Switch14
- Site Specific Data (SSD)14
- Software (S/W) / Firmware / System Program14
- Eblwin14
- Web-Server14
3 Overview15
- The EBL128 C.I.e15
  - Expansion Boards15
  - Power Supply15
- S/W Versions15
- Documents15
- Applications16
- Pc S/W16
4 Control & Indicating Equipment17
- COM Loop19
- Programmable Voltage Outputs (S0-S1)22
- Programmable Relay Output (R0)23
- Relay Output for Routing Equipment (Fault Tx) (R1)23
- Programmable Input (I0)23
- DC Power Supply Outputs24
- RS232 Interfaces24
- RS485 Transceiver (Option)24
- Power Supply24
- Internal Power Supply25
5 Expansion Boards 458X26
- Expansion Board Address Setting27
- Zones Expansion Board 458027
  - Type of Zone Line Input28
  - Input States28
- Relays Expansion Board 458129
- Inputs and Outputs Expansion Board 458329
- I/O Matrix Board 458231
6 Peripheral Devices34
- COM Loop Units34
- Units Connected to the RS485 Interface55
- Units Connected to the RS232 Interface J559
  - Web-Servers59
- Units Connected to the RS232 Interface J360
- Other Units61
7 Programmable Inputs63
- Control Unit Input I0 & Inputs and Outputs Exp. Board 4583, Input 0-464
  - Not Supervised64
  - Supervised64
- 3361 Unit Inputs In0 / Z & In165
8 Input Programming66
- Type (Trigger Conditions)66
- Logic69
  - Not Supervised (Default)69
  - Supervised69
9 Programmable Outputs70
- Control Unit Outputs S0 - S171
- Control Unit Output R072
- Inputs and Outputs Expansion Board 4583 Output 0 - 172
- The 3361 Unit Outputs Re0 - Re172
- The 3364 Unit Outputs VO0, VO1 & VO273
- The 3377 / 4477 Unit Output (Siren)73
- The 3378 Unit Output (Sounder)73
- The 3379 Unit Output (Sounder)73
- The 4380 Unit Output (Beacon)73
- The 4383 Unit Output (Light Indicator)73
10 Output Programming74
- Type74
- Logic75
- Supervised75
- Output Signal Period75
- Control Expression78
  - Trigger Conditions78
- Logical Operators84
  - Control Expression Examples84
11 Interlocking Function88
- Interlocking Programming88
- Interlocking Indications90
- Information of Interlocking Combinations (H9)90
- Interlocking Control Expressions91
12 Fire Door Closing Function92
13 Functions / Services / Features93
- Sensor Value93
- Week Average Sensor Value93
- Decision Value94
- Alarm Algorithms for Smoke Detectors / Detection Levels / Offsets94
  - Alarm Algorithm / Alternative Alarm Algorithm95
  - Filtering Algorithm96
  - Smouldering Smoke Algorithm98
  - Performance Factor99
- Algorithms for Analog Heat Detectors100
  - Class A1 Algorithm100
  - Class A2 S Algorithm101
- Self Verification101
  - Class B S Algorithm101
- Minimum / Maximum Sensor Values102
- 2-Zone / 2-Address Dependence (Co-Incidence Alarm)102
  - 2-Zone Dependence102
  - 2-Address (-Unit) Dependence103
  - Reset of 2-Zone / 2-Address Dependence103
  - Alarm103
- Delayed Alarm103
- Alarm Verification Facility104
- Alert Annunciation105
- Alarm Acknowledgement Facility (AAF)106
- Quiet Alarm109
- Fire Alarm Type a and Fire Alarm Type B109
  - Fire Alarm Type B110
  - Fire Alarm Type a110
- Disable Zones, Alarm Points, Outputs, Etc110
  - Disable Zone111
  - Disable Zone-Address111
  - Disable Output111
  - Disable All Control, Ventilation, Exting or Interlocking Outputs111
  - Disable / Re-Enable Alarm Devices111
  - Disable / Re-Enable Outputs for Routing Equipment111
  - Disable / Re-Enable Alert Annunciation Function111
  - Disconnect / Re-Connect COM Loop112
  - Disconnect / Re-Connect Zone Line Input112
  - Disconnect / Re-Connect Addressable Zone Interface Input112
  - Disable Interlocking Output112
- Test Mode112
- Test Alarm Devices112
- Test of Routing Equipment113
- Calibration of Supervised Outputs113
- Service Signal113
- Fault Signal (Fault Condition)114
- Alarm Texts114
  - Creating the Alarm Texts Via Eblwin114
  - Downloading Texts to the Dus 1728 / 1735 / 1736 and Ext. Fbps 1826 / 1828116
- Real Time Clock (RTC)116
  - Daylight Saving Time117
- Time Channels 1-14117
- Time Channels 15-63117
- Event Log118
- Loss of Main Power Source118
  - Fault: Loss of Main Power Source118
  - LCD Backlight118
- Evacuate118
14 Special New Zealand Functions120
- Alarm Devices120
  - Silence Alarm Devices (Inside Switch)120
  - New Zealand FB Silence Switch (Outside Switch)120
- Battery Faults121
  - FAULT: Battery121
  - FAULT: Low Battery Capacity121
- Watchdog Reset122
- Routing Equipment Isolate (Disable)122
- Acknowledged Alarm122
15 Advanced Mode123
- Pulse up - down Counter124
  - Pulse up - down Counter for Smoke124
  - Pulse up - down Counter for Temperature124
- Fire Judgement125
  - Pulse up - down Counter for Smoke & Temperature125
- Alarm Threshold Levels125
- Alarm Delay Time126
- Learning Function / Learning Period127
  - Area Alarm Algorithms127
- Analog Data Output128
- Sensitivity Compensation129
- Self Diagnosis of Internal Devices129
- Address Setting Check130
- Polling LED130
16 Control Unit Properties131
- Control Unit Properties Dialog Box131
- Eblwin Control Unit Pop-Up Menu132
17 System Properties (Settings)134
- System Properties Dialog Box134
18 Eblwin Menus138
- The File Menu138
- The View Menu139
- The System Menu142
- The Tools Menu150
- The Help Menu152
19 Download SSD153
- COM Loop Menu153
  - Check Loop153
  - Auto Generate Loop154
- SSD Download to the Control Unit154
- User Definable Text Messages Download155
20 Download Software (S/W)156
- Software Download to the Control Unit156
21 Cable Types158
- COM Loop Cables158
- Ext. FBP / EPU / AAU Cables158
- Conventional Zone Line Cables158
- Alarm Device Cables158
- Other Equipment Cables158
22 COM Loop Cable Length159
23 Current Consumption162
24 Power Supply167
- Charger Functions167
  - Battery Charging Functions168
  - Security Functions168
- Current Consumption Calculations169
- Main Power Source (Power Supply)170
- Second Power Source (Battery)170
- Form / Table of Current Consumption171
25 W Versions172
26 Technical Data173
27 Limitations174
28 National Regulations / Requirements175
- Conventions175
- Language175
29 Drawings / Connection Diagrams176
30 Revision History177

Table of Contents

Other manuals for Panasonic EBL128

Related product manuals