Panasonic KX-FP215

64
KX-FP215
580 TAM continuous tone detection 1: ON
2: OFF
1, 2 1 ON : Stops TAM operation when Dial tone, etc. are
detected.
590 FAX auto redial time set × number of
times
00~99 01 Selects the number of redial times during FAX
communication (not including the first dial).
591 FAX auto redial time disconnection
time set
× second 001~999 065 Sets the FAX redial interval during FAX
communication.
592 CNG transmit select 1: OFF
2: ALL
3: AUTO
1~3 2 Lets you select the CNG output during FAX
transmission. ALL: CNG is output at phase A. AUTO:
CNG id output only when automatic dialing is
performed. OFF: CNG id not output at phase A. Refer
to Sometime there is a transmit problem (P.88).
593 Time between CED and 300bps 1: 75 msec
2: 500 msec
3: 1 sec
1~3 1 See Symptom/Countermeasure Table for long
distance and international calls in The unit can copy,
but cannot either transmit/receive long distance or
international communications (P.91). Refer to
Receive Problem (P.89) .
594 Overseas DIS detection select 1:detects at
the 1st time
2:detects at
the 2st time
1, 2 1 See Symptom/Countermeasure Table for long
distance and international calls in The unit can copy,
but cannot either transmit/receive long distance or
international communications (P.91). Refer to
Sometime there is a transmit problem (P.88).
595 Receive error limit value set 1: 5 %
2: 10 %
3: 15 %
4: 20%
1~4 2 Refer to Receive Problem (P.89).
596 Transmit level set × dbm
(10 = -10 dbm)
-15~00 10 Selects the FAX transmission level. Refer to Sometime
there is a transmit problem (P.88) and Receive
Problem (P.89).
598 Receiving sensitivity × dbm
(40 = -40 dbm)
-20~-48 42 Used when there is an error problem. Refer to The unit
can copy, but cannot either transmit/receive long
distance or international communications (P.91).
Power is OFF/ON after changing this set value.
599 ECM frame size 1: 256 byte
2: 64 byte
1, 2 1 ----------
625 Setting printing density 1: Default
2: Lighter
3: Darker
1~3 1 The set value “2“ means lighter than default density.
The set value “3“ means lighter than default density.
710 Memory clear except History data Refer to Memory Clear Specification (P.65).
717 Transmit speed selection 1: 14400 BPS
2: 12000 BPS
3: 9600 BPS
4: 7200 BPS
5: 4800 BPS
6: 2400 BPS
1~6 1 Adjusts the speed to start training during FAX
transmission. Refer to Sometime there is a transmit
problem (P.88) and The unit can copy, but the
transmission and reception image are incorrect
(P.93).
718 Receive speed selection 1: 14400 BPS
2: 12000 BPS
3: 9600 BPS
4: 7200 BPS
5: 4800 BPS
6: 2400 BPS
1~6 1 Adjusts the speed to start training during FAX
reception. Refer to Receive Problem (P.89) and The
unit can copy, but the transmission and reception
image are incorrect (P.93).
722 Redial tone detect 1: ON
2: OFF
1, 2 2 Sets the tone detection mode after redialing.
732 AUTO disconnect cancel time 1: 2 sec
2: 4 sec
3: OFF
1~3 1 “Set to “2” when the auto disconnect circuit operates
and cuts the line.”
745 Power ON film feed 1: ON
2: OFF
1, 2 1 When the power is turned on, the film is wound to take
up any slack.
763 CNG detect time for friendly reception 1: 10 sec
2: 20 sec
3: 30 sec
1~3 3 Selects the CNG detection tone of friendly reception.
773 DIS-DIC interval 1: 500 msec
2: 200 msec
1, 2 2 This is similar to #594. The time interval from receiving
DIS to sending DCS can be changed to wait for the
echo canceler to recover.
774 T4 timer × 100 msec 00~99 00 Use this function when delay occurs in the line and
communication (ex. Mobile comm) does not work well.
Code Function Set Value Effective
Range
Default Remarks