Panasonic KX-FPG381

8. Programmable Features
76
3. Scroll to “Set answering” by pressing {v}
or {e}, and press {>}.
4. Scroll to “Recording time” by pressing
{v} or {e}, and press {>}.
5. Press {v} or {e} repeatedly to select the
desired setting.
L You can also select the recording time by
pressing a dialing button {1} (1 minute),
{2} (2 minutes), {3} (3 minutes) or {0}
(“Greeting only”).
6. Press the right soft key ({SAVE}).
7. Press {OFF}.
Note:
L If you select “Greeting only”, the unit will
answer a call with the greeting message, and
then hang up. The unit will not record any
incoming messages.
L You can also program this feature with the
base unit (feature #10 on page 69).
Setting remote operation code
Make sure the base unit and the handset are
not being used.
1. Press {CONF/FUNCTION}.
2. Scroll to “Initial setting” by pressing
{v} or {e}, and press {>}.
3. Scroll to “Set answering” by pressing {v}
or {e}, and press {>}.
4. Scroll to “Remote code” by pressing {v} or
{e}, and press {>}.
5. Enter a remote code using a 2-digit number
(00–99).
L The default setting is “11”.
6. Press the right soft key ({SAVE}).
7. Press {OFF}.
Note:
L You can also program this feature with the
base unit (feature #11 on page 69).
Setting the mailbox 2 or 3 password
To prevent other users from retrieving your
messages, program a password for mailbox 2 or
3.
Make sure the base unit and the handset are
not being used.
1. Press {CONF/FUNCTION}.
2. Scroll to “Initial setting” by pressing
{v} or {e}, and press {>}.
3. Scroll to “Set answering” by pressing {v}
or {e}, and press {>}.
4. Scroll to “Set mailbox2&3” by pressing
{v} or {e}, and press {>}.
5. Select the mailbox by pressing {e}
(“Mailbox2”) or {v} (“Mailbox3”).
L If the password has previously been
assigned to the mailbox, it is displayed.
6. Enter a 2-digit number (00–99).
L If you entered a wrong number, press
{HOLD/CLEAR} and enter the password
again.
7. Press the right soft key ({SAVE}).
8. Press {OFF}.
To check the password
Repeat steps 1 to 5.
L The password is displayed. When finished,
press {OFF}.
To erase the password
Press {HOLD/CLEAR} in step 6, and press the
right soft key ({SAVE}), then press {OFF}.
L You will be able to access the mailbox without
entering the password.
Note:
L You can also program this feature with the
base unit (feature #51 on page 71 and
feature #52 on page 71).
Setting the room monitor feature
See page 48 for details. To turn ON the base unit
room monitor feature using the handset,
program as follows:
Use the handset. Make sure the base unit and
the handset are not being used.
1. Press {CONF/FUNCTION}.
2. Scroll to “Initial setting” by pressing
{v} or {e}, and press {>}.
3. Scroll to “Set base unit” by pressing {v}
or {e}, and press {>}.
4. Scroll to “Room monitor” by pressing {v}
or {e}, and press {>}.
5. Press {v} or {e} repeatedly to select the
desired setting.
6. Press the right soft key ({SAVE}).
Note:
L You can also set the base unit room monitor
feature using the base unit (feature #74 on
page 48).
0519_FPG381.book Page 76 Monday, May 19, 2003 6:46 PM