To Next PageTo Next PageWhy is the color pale on my Panasonic Projector?
If the color on your Panasonic Projector appears pale or grayish, try adjusting the [Color] and [Tint] settings. Check the settings of the input source connected to the projector. If you are using an RGB cable, replace it if it's damaged.
How to fix a fuzzy picture on a Panasonic PT-CW230E?
If you're experiencing a fuzzy picture with your Panasonic Projector, try adjusting the lens focus. Also, adjust the distance between the projector and the screen. Clean the projection window, and make sure the projector isn't tilted too much.
Why is there no illumination on Panasonic PT-CW230E?
If there is no illumination or flashing on the ON(G)/STANDBY(R) indicator of your Panasonic Projector, it might be due to the power cord being unplugged. Make sure to plug in the power cord.
Why does my Panasonic Projector remote control not operate?
If the remote control for your Panasonic Projector isn't working, start by replacing the batteries. Make sure the batteries are inserted correctly. Check for any obstructions blocking the signal receptor on the projector. Ensure the remote is within the operational range, and avoid strong light shining on the signal receptor. Finally, make sure the same codes are set on both the projector and the remote control.
What to do if no picture appears on my Panasonic PT-CW230E Projector?
If you're not getting any picture on your Panasonic Projector, first, ensure that the video signal input source is correctly connected to the appropriate terminal. Then, check the input selection setting on the projector. Increase the [Brightness] adjustment if it's set too low. Verify that the connected input source is working correctly, and make sure the [AV mute] function is turned off.
What to do if the temperature inside Panasonic PT-CW230E Projector is abnormally high and the WARNING indicator also blinks in red?
If the temperature inside your Panasonic Projector is abnormally high (and the WARNING indicator also blinks in red), the projector cannot be turned on until cooling is completed. Wait until cooling is completed and the ON(G)/STANDBY(R) indicator stops blinking.
What to do if Panasonic PT-CW230E Projector detects an abnormal condition and cannot be turned on?
If your Panasonic Projector detects an abnormal condition and won't turn on, unplug the AC power cord and then plug it back in to try turning it on again.
General| Matrix size | 0.65 \ |
|---|---|
| Number of colors | 16.78 million colors |
| Native aspect ratio | 16:10 |
| Projection distance | - m |
| Vertical scan range | 50 - 120 Hz |
| Horizontal scan range | 15 - 93 kHz |
| Projection technology | DLP |
| Contrast ratio (typical) | 2000:1 |
| Screen size compatibility | 6 - 110 \ |
| Projector native resolution | WXGA (1280x800) |
| Vertical synchronization (max) | 120 kHz |
| Vertical synchronization (min) | 50 kHz |
| Horizontal synchronization (max) | 93 kHz |
| Horizontal synchronization (min) | 15 kHz |
| RS-232 ports | 0 |
| Focus | Manual |
| Focal length range | - mm |
| Aperture range (F-F) | 2.5 - 2.5 |
| Lamp type | UHM |
| Lamp power | 275 W |
| Lamps quantity | 1 lamp(s) |
| Light source type | Lamp |
| Service life of light source | 3000 h |
| HDCP | Yes |
| Noise level | 36 dB |
| Noise level (economic mode) | 28 dB |
| Dot clock scanning frequency | 150 MHz |
| Full HD | No |
| Supported video modes | 1080i, 480i, 480p, 576i, 576p, 720p |
| Analog signal format system | NTSC, NTSC 4.43, PAL 60, PAL M, PAL N, SECAM |
| Supported graphics resolutions | 720 x 576, 1280 x 720 (HD 720), 1280 x 800 (WXGA), 1920 x 1080 (HD 1080), 854 x 480 (WVGA) |
| Audio (L/R) in | 3 |
| USB 2.0 ports quantity | USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them. |
| Placement | Desktop |
| Product type | Short throw projector |
| Product color | White |
| Market positioning | Short throw |
| Power source | AC |
| Power consumption (standby) | 0.45 W |
| Power consumption (typical) | 350 W |
| Operating temperature (T-T) | 0 - 40 °C |
| Operating relative humidity (H-H) | 20 - 80 % |
| Cables included | AC, VGA |
Weight and Dimensions| Depth | 386 mm |
|---|---|
| Width | 321 mm |
| Height | 178 mm |
| Weight | 6200 g |
Ensures proper grounding and electrical safety precautions.
Protects against moisture, UV lamp hazards, and heat exposure.
Guidelines for safe handling of power cords, plugs, and outlets.
Safe placement advice for projector installation and operating environment.
Ensures correct installation work and use of safety measures like wires.
Advises against foreign objects, disassembly, and contact with liquids.
Proper handling, storage, and precautions for battery usage and leakage.
Instructions for safely disconnecting the power cord to prevent damage.
Safe usage conditions, avoiding hot locations and proper cable handling.
Guidance on safe handling and precautions related to the lamp unit.
Highlights features like Auto Setup, LAN, 3D, and Direct Power Off.
Provides a concise, step-by-step guide for initial projector setup.
Covers handling, vibration, impacts, and adjustable feet during transport.
Safe installation advice for environment, elevation, and ventilation.
Ensures correct placement, ventilation, and avoids blocking air ports.
Covers password management and network security measures.
Guidelines for the proper disposal of the projector, lamp, and batteries.
Advice on maintaining picture quality and caring for optical components.
Guidance on lamp life, bursting, and safe 3D viewing practices.
Recommendations for ambient light and lighting conditions for 3D viewing.
Advises viewing restrictions for children, photosensitive, and ill individuals.
Lists included accessories like remote, cables, and CD-ROM contents.
Details optional brackets, lamp units, and filter units.
Explains the function of each button on the remote control unit.
Covers signal reception, operating range, and handling advice.
Diagram identifying external parts of the projector body.
Caution regarding heat emitted from the air exhaust port.
Details the functions of buttons on the projector's control panel.
Description of various input/output terminals and their uses.
Step-by-step guide for installing and removing batteries.
Setting unique IDs for operating multiple projectors with one remote.
Describes six different projection methods for various setups.
Details compatible mounting brackets and installation requirements.
Provides a diagram and table for projection distances for PT-CW230E.
Attention and notes regarding DLP projectors and laser equipment.
Provides projection distance data and calculation formulas for PT-CX200E.
Procedure for adjusting the projector's front feet for height and tilt.
Important notes on air exhaust and keystone distortion during adjustment.
Covers power off, cables, TBC, and supported signal types.
Illustrates connections and provides notes on HDMI and network.
Describes the power cord holder and steps for attaching the cord.
Visual guide showing the correct method for securing the power cord.
Explains the projector's power status based on the indicator light.
Step-by-step guide for turning on the projector and selecting input.
Describes what appears on screen during power-on and signal input.
Instructions for entering the projector's PIN code via dialog box.
Information on PIN entry timeout and the initial factory PIN.
Step-by-step guide for properly shutting down the projector.
Allows disconnecting power without using the power button.
Guide to selecting input sources like HDMI, Computer, and Video.
Covers zoom, image position adjustment, and focus lever operation.
Lists necessary equipment, content, and signal types for 3D projection.
Procedures for using DLP Link and IR wireless emitter 3D glasses.
Covers switching input signals and using the Auto Setup function.
Explains how to select different screen modes using the SCREEN button.
Using KEYSTONE for distortion correction and INFO. for display.
Pauses the projected image and mutes sound temporarily.
Controls for AV MUTE function and digital zoom (D.ZOOM).
Adjusting volume, selecting lamp modes, and image modes.
Activating and controlling the 3D display function.
Temporarily muting or unmuting the projector's audio output.
Step-by-step guide for navigating and operating the projector's menu.
Describes how unavailable menu items are shown and their conditions.
Lists the nine main menu categories for projector settings.
Details the options available within the Input and PC Adjust submenus.
Lists settings for image adjustments and screen aspect ratio.
Lists options for sound, general settings, and system information.
Settings for Computer 1 input: RGB, Component, and RGB(Scart).
Configuring Computer 2 input and projector system selection.
Procedure for connecting and configuring the HDMI input source.
Procedures for configuring Video and S-Video input sources.
Procedure to automatically adjust sync, dots, and position.
Notes on signal compatibility and limitations of auto adjustment.
Detailed procedures for adjusting horizontal and vertical image positions.
Adjusting fine sync, total dots, and other parameters.
Procedures for clamp level, resetting data, and clearing modes.
How to store and recall custom PC adjustment settings.
Descriptions and selection procedures for preset image modes.
Procedure for selecting and using user-defined image presets.
Procedures for adjusting color intensity, contrast, and brightness.
Adjusting color tint and selecting desired color temperature.
Procedures for adjusting red, green, and blue color tones.
Adjusting sharpness, gamma, and applying noise reduction.
Options and notes for displaying interlaced video in progressive mode.
Procedures for resetting adjustments and storing custom settings.
Descriptions and procedures for standard screen modes.
Descriptions and procedures for advanced screen modes.
Manual adjustment for screen scale and position using Custom adj.
Procedures for digital zoom and keystone distortion correction.
Procedures for ceiling, rear projection, and colorboard modes.
Setting the screen aspect ratio to 4:3 or 16:9.
Procedure for controlling the projector's speaker volume.
Instructions for muting and unmuting the audio output.
Changing the on-screen menu position and selecting the display language.
Configuring automatic signal detection and input search.
Configuring 3D mode, sync inversion, and phase adjustment.
Memorizing zoom settings, selecting background, and display options.
Setting startup logos, locking logo changes, and changing PIN codes.
Configuring HDMI input settings and terminal output options.
Configuring power saving modes, standby options, and timers.
Setting timers, direct power on, and closed caption display.
Adjusting screen brightness via lamp power and setting remote control codes.
Enabling key lock for panel/remote and PIN code for projector operation.
Changing PIN code and adjusting fan speed based on altitude.
Checking cumulative lamp usage time and resetting the timer.
Setting filter replacement frequency and resetting the filter counter.
Procedure to reset all settings to their original factory defaults.
Displays input source, sync frequencies, and screen size.
Shows lamp status, power management, security, and serial number.
Explains the yellow LAMP indicator and actions for lamp replacement.
Explains the red WARNING indicator for abnormal conditions.
Instructions for cleaning the projector's outer case and projection window.
Step-by-step guide for replacing the air filter unit.
Procedure to reset the filter counter after replacing the air filter unit.
Caution on hot replacement, handling glass, and mercury disposal.
When to replace lamp, indicators, and replacement steps.
Detailed steps for removing the old lamp unit and installing a new one.
Procedure to reset the lamp runtime after replacement.
Troubleshooting for power issues, no picture, and fuzzy images.
Diagnosing sound, remote control, and computer input problems.
Resolving HDMI connection issues and image distortion.
Addressing 3D mode, image inversion, flicker, and glasses issues.
Diagram and pin assignments for serial terminal connection.
Details on communication conditions and cable specifications.
Format for sending commands to control the projector.
Table detailing commands for various projector functions.
Format for reading projector status information.
Table of command codes and their corresponding projector statuses.
Pin assignments for the S-Video input terminal.
Pin assignments for Computer 1/Component and Computer 2 terminals.
Detailed pin assignments for the HDMI terminal.
Pin assignments for the 3D Sync Output terminal.
Table detailing compatibility for NTSC, PAL, and VGA signal types.
Table detailing compatibility for SVGA and MAC signal types.
Table detailing compatibility for XGA and WXGA signal types.
Table detailing compatibility for WSXGA+ and WUXGA signal types.
Table detailing compatibility for UXGA and WXGA signal types.
Table detailing compatibility for various D-series signal types.
Provides detailed compatibility information for D-series signal types.
Details model, power, DLP chip, lens, and light output specifications.
Covers scanning frequency, color system, size, and speaker specs.
Detailed specifications for all projector terminals.
Information on dimensions, weight, and operating environment.
Illustrations showing projector dimensions with measurements.
Safety guidelines and torque specifications for ceiling mount brackets.
Explains symbols and general guidelines for disposing of electronics and batteries.
Provides disposal guidelines specific to the EU and other regions.
