Chapter 4 Settings — [PROJECTOR SETUP] menu
144 - ENGLISH
[SIGNAL INFORMATION]
[INPUT] Displays the input terminal used for the projected image.
[SIGNAL FORMAT] Displays the format of the input signal.
[SIGNAL FREQUENCY] Displays the frequency of the input signal.
[SYNC.STATE] Displays the sync polarity of the input signal.
[V.SYNC WIDTH] Displays the vertical sync signal pulse width of the input signal.
[SCAN TYPE] Displays the scan type of the input signal.
[TOTAL DOTS] Displays the total dot count of the input signal.
[DISPLAY DOTS] Displays the number of input signal display dots.
[TOTAL LINES] Displays the total line count of the input signal.
[DISPLAY LINES] Displays the number of input signal display lines.
[SAMPLING] Displays the sampling information of the input signal.
[SIGNAL LEVEL] Displays the signal level of the input signal.
[BIT DEPTH] Displays the gradation of the input signal.
[HDCP STATUS]
Displays the HDCP status of the input signal. The content of display
is as follows.
[HDCP2.2]: When protected with HDCP 2.2
[HDCP1.X]: When protected with HDCP 1.X
[NONE]: When not protected with HDCP
*1 The temperature status is indicated with text color (green/yellow/red) and bar scale. Use the projector within the range that the indication is
green.
*2 [CONSOLIDATED RUNTIME] can be obtained with the following calculation formula. Values obtained by the calculation formula contain a
slight error.
Conversion formula for [CONSOLIDATED RUNTIME]
A x 1.0 + B x 0.8
f A: Runtime of the light source with [OPERATING MODE] set to [NORMAL], [QUIET1], [QUIET2], [USER1], [USER2], or [USER3]
f B: Runtime of the light source with [OPERATING MODE] set to [ECO]
Note
f E-mail containing the status can be sent to the E-mail address (up to two addresses) set in “[E-mail set up] page” (x page 174) by
pressing the <ENTER> button while the [STATUS] screen is displayed.
f Some items in [SIGNAL INFORMATION] may be displayed and others not displayed, depending on the signal being input.
f If any abnormality has occurred on the projector, press the <DEFAULT> button while the [STATUS] screen is displayed to display the detail
screen of the error information.
f For details on the contents displayed in [SELF TEST], refer to “[SELF TEST] indications” (x page 189).
[DATA CLONING]
Perform the operations of the data cloning function. Data such as the settings and adjustment values of the
projector can be copied to multiple projectors via LAN.
r Data that cannot be copied
The following settings cannot be copied. Set these in each projector.
f The [PROJECTOR SETUP] menu → [PROJECTOR ID]
f The [PROJECTOR SETUP] menu → [DATE AND TIME] → [ADJUST CLOCK]
f The [PROJECTOR SETUP] menu → [DATA CLONING] → [WRITE PROTECT]
f The [SECURITY] menu → [SECURITY PASSWORD]
f The [NETWORK] menu → [NETWORK SETUP]
f Security password
f Control device password
f Password set in “[Change password] page” (x page 178) of the web control screen
f “[E-mail set up] page” (x page 174) in the web control screen
f “[Authentication set up] page” (x page 175) in the web control screen
f “[Crestron Connected(TM)] page” (x page 180) in the web control screen
Copying data to another projector
Set the following settings on the projector to copy the data in advance. Refer to “Setting [WRITE PROTECT]”
(x page 145) for details.
f The [PROJECTOR SETUP] menu → [DATA CLONING] → [WRITE PROTECT] → [OFF]
1) Connect all projectors to the hub using LAN cables. (x page 162)
To Next Page
Loading...
