Panasonic PT-RZ31K

Chapter 4 Settings — [PROJECTOR SETUP] menu
ENGLISH - 153
2) Press the <ENTER> button.
f The [STATUS] screen is displayed.
3) Press qw to switch the pages.
f The page will change each time you press the button.
[PROJECTOR TYPE] Displays the projector type and serial number of the projector.
[PROJECTOR RUNTIME] Displays the runtime of the projector.
[LIGHT RUNTIME] Displays the runtime of the light source 1 and the light source 2.
[MAIN/SUB VERSION] Displays the main and sub versions of the rmware of the projector.
[INTAKE AIR TEMP.]
*1
Displays the status of the intake air temperature of the projector.
[OPTICS MODULE TEMP.]
*1
Displays the status of the internal temperature of the projector.
[EXHAUST AIR TEMP.]
*1
Displays the status of the exhaust air temperature of the projector.
[LIGHT1-B TEMP.]
*1
Displays the light source 1 temperature status of the projector.
[LIGHT1-S TEMP.]
*1
[LIGHT2-B TEMP.]
*1
Displays the light source 2 temperature status of the projector.
[LIGHT2-S TEMP.]
*1
[SELF TEST] Displays the status of the projector.
[INPUT]
Displays the input terminal currently selected.
Displays the representative input terminal when one image is displayed with multiple input signals.
[SIGNAL NAME] Displays the input signal name.
[MEMORY NO.] Displays the memory number of the input signal.
[BACKUP INPUT STATUS]
Displays whether switching to the backup input signal is possible or not when [BACKUP INPUT
MODE] is set to [OFF]. (x page 116)
[NUMBER OF REGISTERED
SIGNAL]
Displays the number of registered signals.
[COOLING CONDITION] Displays the set cooling conditions.
[ATMOSPHERIC PRESSURE] Displays the atmospheric pressure.
[REMOTE2 STATUS] Displays the control status of the REMOTE2.
[AC VOLTAGE] Displays the input supply voltage.
[ON COUNT]
[POWER ON TIMES] Displays the number of times the power is turned on.
[MECHANICAL SHUTTER]
Displays the number of times the mechanical shutter is closed.
It is counted when [MECHANICAL SHUTTER] is set to [ENABLE].
[FILTER TYPE]
Displays the setting of the [PROJECTOR SETUP] menu → [FILTER SETTING] → [FILTER TYPE].
[FILTER COUNTER]
*2*3
Displays the runtime of the lter (counter numeric value) and the recommend time to replace the lter.
[OPERATING MODE]
Displays the setting value of the [PROJECTOR SETUP] menu → [OPERATION SETTING] →
[OPERATING MODE].
[HIGH] Displays the runtime of the light source with [OPERATING MODE] set to [HIGH].
[NORMAL] Displays the runtime of the light source with [OPERATING MODE] set to [NORMAL].
[LONG LIFE1] Displays the runtime of the light source with [OPERATING MODE] set to [LONG LIFE1].
[LONG LIFE2] Displays the runtime of the light source with [OPERATING MODE] set to [LONG LIFE2].
[LONG LIFE3] Displays the runtime of the light source with [OPERATING MODE] set to [LONG LIFE3].
[USER1] Displays the runtime of the light source with [OPERATING MODE] set to [USER1].
[USER2] Displays the runtime of the light source with [OPERATING MODE] set to [USER2].
[USER3] Displays the runtime of the light source with [OPERATING MODE] set to [USER3].
[CONSOLIDATED RUNTIME]
*4
Converts the total runtime of the light sources with [OPERATING MODE] set to each item into the
time used with the [NORMAL] setting.
The converted runtime is used for a rough indication about when to perform maintenance when the
projector is used in combination of each item in [OPERATING MODE].
[UPGRADE KIT]
[ET-UK20]
Displays the activation status by the Upgrade Kit (Model No.:
ET-UK20).
[ET-CUK10]
Displays the activation status by the Auto Screen Adjustment
Upgrade Kit (Model No.: ET-CUK10).