Panasonic PT-RZ31K

Chapter 4 Settings — [PROJECTOR SETUP] menu
154 - ENGLISH
[SIGNAL INFORMATION]
[INPUT]
Displays the input terminal used for the projected image.
Displays the representative input terminal when one image is
displayed with multiple input signals.
[SIGNAL FORMAT] Displays the format of the input signal.
[LINK]
Displays the [SDI LINK] setting.
Displays the determination result of the signal when set to [AUTO].
[2D/3D] Displays the determination results of the 2D/3D display
[SIMUL]
Displays the [SIMUL INPUT SETTING] setting.
Displays the determination result of the signal when set to
[AUTO(3D)] or [AUTO(2D)].
[COLOR FORMAT] Displays the color format of the input signal.
[SAMPLING] Displays the sampling information of the input signal.
[BIT DEPTH] Displays the gradation of the input signal.
[SIGNAL LEVEL] Displays the signal level of the input signal.
[DETAILED INFORMATION]
[INPUT] Displays the input terminal used for the projected image.
[SIGNAL FORMAT] Displays the format of the input signal.
[SIGNAL FREQUENCY] Displays the frequency of the input signal.
[SCAN TYPE] Displays the scan type of the input signal.
[TOTAL DOTS] Displays the total dot count of the input signal.
[DISPLAY DOTS] Displays the number of input signal display dots.
[TOTAL LINES] Displays the total line count of the input signal.
[DISPLAY LINES] Displays the number of input signal display lines.
[COLOR FORMAT] Displays the color format of the input signal.
[SAMPLING] Displays the sampling information of the input signal.
[BIT DEPTH] Displays the gradation of the input signal.
[SIGNAL LEVEL] Displays the signal level of the input signal.
*1 The temperature status is indicated with text color (green/yellow/red) and bar scale. Use the projector within the range that the indication is
green.
*2 In the following cases, the recommended time to replace the lter is not set, and it is not displayed.
When the [PROJECTOR SETUP] menu → [OPERATION SETTING] → [OPERATING MODE] is set to [NORMAL], [USER1], [USER2], or
[USER3], and the [PROJECTOR SETUP] menu → [FILTER SETTING] → [FILTER TYPE] is set to [LONG LIFE]
When the [PROJECTOR SETUP] menu → [OPERATION SETTING] → [OPERATING MODE] is set to [LONG LIFE1], [LONG LIFE2], or
[LONG LIFE3]
*3 If the runtime of the lter exceeds the recommended time to replace the lter, the runtime is displayed in red.
*4 [CONSOLIDATED RUNTIME] can be obtained with the following calculation formula. Values obtained by the calculation formula contain a
slight error.
Conversion formula for [CONSOLIDATED RUNTIME]
A x 2.5 + B x 1.0 + C x 0.5 + D x 0.3 + E x 0.2
f A: Runtime of the light source with [OPERATING MODE] set to [HIGH]
f B: Runtime of the light source with [OPERATING MODE] set to [NORMAL], [USER1], [USER2], or [USER3]
f C: Runtime of the light source with [OPERATING MODE] set to [LONG LIFE1]
f D: Runtime of the light source with [OPERATING MODE] set to [LONG LIFE2]
f E: Runtime of the light source with [OPERATING MODE] set to [LONG LIFE3]
Note
f The content of the status can be sent to the E-mail address (up to two addresses) set in “[E-mail set up] page” (x page 184) when the
<ENTER> button is pressed while displaying the pages 1/6 to 5/6 of the [STATUS] screen.
f The detailed information of the input signal is displayed when the <ENTER> button is pressed while displaying the page 6/6 of the
[STATUS] screen. Information for multiple input signals may be displayed depending on the projected image. Press qw to switch pages.
f There are items that are displayed or not displayed in [SIGNAL INFORMATION] and [DETAILED INFORMATION] depending on the setting
or the input signal.
f If any abnormality has occurred on the projector, press the <DEFAULT> button while the [STATUS] screen is displayed to display the detail
screen of the error information.
f For details on the contents displayed in [SELF TEST], refer to “Self-diagnosis display” (x page 206).
[AC VOLTAGE MONITOR]
Enable or disable the AC voltage monitor function. The value of input supply voltage is displayed on the self-
diagnosis display at the side of the projector when enabled.
1) Press as to select [AC VOLTAGE MONITOR].
2) Press qw to switch the item.
f The items will switch each time you press the button.