Panasonic PT-RZ31K

Chapter 4 Settings — [PROJECTOR SETUP] menu
ENGLISH - 155
[OFF] Disables the AC voltage monitor function.
[ON] Enables the AC voltage monitor function.
Note
f When [ON] is set, the value of the input supply voltage is always displayed in the self-diagnosis display while the main power of the projector
is turned on.
f Even when [OFF] is set, the value of input supply voltage can be displayed temporarily in the self-diagnosis display by operating the button
on the remote control. (x page 79)
f The value of input supply voltage cannot be displayed in the self-diagnosis display during standby when the [PROJECTOR SETUP] menu
→ [STANDBY MODE] (x page 142) is set to [ECO].
[FILTER SETTING]
Set the type of lter. The lter runtime (counter numeric value) can also be reset.
Setting [FILTER TYPE]
Set the type of lter attached to the projector.
1) Press as to select [FILTER SETTING].
2) Press the <ENTER> button.
f The [FILTER SETTING] screen is displayed.
3) Press as to select [FILTER TYPE].
f The [FILTER TYPE] screen is displayed.
4) Press qw to switch the item.
f The items will switch each time you press the button.
[NORMAL]
Factory default setting. Select this item when the Replacement Filter Unit (Model No.: ET-EMF330)
(accessory/optional accessory) is attached to the projector.
When the [PROJECTOR SETUP] menu → [OPERATION SETTING] → [OPERATING MODE] is set
to [HIGH], the recommend time to replace the lter is set to 2 000 hours.
When the [PROJECTOR SETUP] menu → [OPERATION SETTING] → [OPERATING MODE] is
set to [NORMAL], [USER1], [USER2], or [USER3], the recommend time to replace the lter is set to
4 000 hours.
When the [PROJECTOR SETUP] menu → [OPERATION SETTING] → [OPERATING MODE] is set
to [LONG LIFE1], [LONG LIFE2], or [LONG LIFE3], the recommended time to replace the lter is not
set.
[LONG LIFE]
Select this item when the optional Long Life Filter Unit (Model No.: ET-EMFU330) is attached to the
projector.
When the [PROJECTOR SETUP] menu → [OPERATION SETTING] → [OPERATING MODE] is set
to [HIGH], the recommend time to replace the lter is set to 4 000 hours.
When the [PROJECTOR SETUP] menu → [OPERATION SETTING] → [OPERATING MODE] is set
to anything other than [HIGH], the recommended time to replace the lter is not set.
[SMOKE CUT]
Select this item when the optional Smoke Cut Filter (Model No.: ET-SFR330) is attached to the
projector.
When the [PROJECTOR SETUP] menu → [OPERATION SETTING] → [OPERATING MODE] is set
to [HIGH], the recommend time to replace the lter is set to 50 hours.
When the [PROJECTOR SETUP] menu → [OPERATION SETTING] → [OPERATING MODE] is set
to [NORMAL], [USER1], [USER2], or [USER3], the recommend time to replace the lter is set to 100
hours.
Note
f The [PROJECTOR SETUP] menu → [OPERATION SETTING] → [OPERATING MODE] cannot be set to [LONG LIFE1], [LONG LIFE2],
or [LONG LIFE3] when [FILTER TYPE] is set to [SMOKE CUT]. Set [OPERATING MODE] to [HIGH], [NORMAL], [USER1], [USER2], or
[USER3] when using the optional Smoke Cut Filter (Model No.: ET-SFR330).
f If the runtime of the lter exceeds the recommended time to replace the lter that is set, the time is displayed in red in the following menu.
Perform maintenance or replacement of the lter.
g [FILTER SETTING] → [FILTER COUNTER RESET]
g [STATUS] → [FILTER COUNTER]
f Perform maintenance or replacement of the lter in the following cases.
g The lter is clogged, causing the lter replacement message to appear on the screen and the lter indicator <FILTER> to light in red.
f Continuing to use the projector with incorrect settings may cause failure.
Resetting [FILTER COUNTER]
Reset the lter runtime (counter numeric value).