Panasonic PT-RZ31K

Chapter 7 Appendix — Specications
234 - ENGLISH
f When using the projector at an altitude between 2 700 m (8 858') and 4 200 m (13 780') above sea level: 25 °C (77 °F)
When the [PROJECTOR SETUP] menu → [OPERATION SETTING] → [OPERATING MODE] is set to [LONG LIFE1], [LONG LIFE2], or [LONG
LIFE3], and the operating environment temperature exceeds 35 °C (95 °F), the light output may be reduced to protect the projector.
Note
f The light output will decrease to approximately 1/3 when using the projector with AC 100 V to AC 120 V.
f The model numbers of accessories and optional accessories are subject to change without prior notice.
r Terminal
<RGB 1 IN> terminal
1 set (BNC x 5 (RGB/YP
B
P
R
/YC
B
C
R
/YC/VIDEO x 1))
RGB signal 0.7 V [p-p] 75 Ω (SYNC ON GREEN: 1.0 V [p-p] 75 Ω)
SYNC/HD TTL high impedance, automatic positive/negative
polarity compatible
VD TTL high impedance, automatic positive/negative
polarity compatible
YP
B
P
R
signal Y: 1.0 V [p-p] including synchronization signal, P
B
P
R
: 0.7 V [p-p] 75 Ω
Y/C signal Y: 1.0 V [p-p], C: 0.286 V [p-p] 75 Ω
VIDEO signal 1.0 V [p-p] 75 Ω
<RGB 2 IN> terminal
1 set, high-density D-Sub 15 p (female)
RGB signal 0.7 V [p-p] 75 Ω (SYNC ON GREEN: 1.0 V [p-p] 75 Ω)
SYNC/HD TTL high impedance, automatic positive/negative
polarity compatible
VD TTL high impedance, automatic positive/negative
polarity compatible
YP
B
P
R
signal Y: 1.0 V [p-p] including synchronization signal, P
B
P
R
: 0.7 V [p-p] 75 Ω
<DVI-D IN> terminal 1 set, DVI-D 24 p, single link, DVI 1.0 compliant, HDCP compatible
<HDMI IN> terminal 1 set, HDMI 19 p, HDCP compatible, Deep Color compatible
<SDI IN 1> terminal
1 set (BNC)
SD-SDI signal SMPTE ST 259 compliant
HD-SDI signal SMPTE ST 292 compliant
3G-SDI signal SMPTE ST 424 compliant
Dual link HD-SDI
(LINK-A) signal
SMPTE ST 372 compliant
Dual link 3G-SDI (Link
1) signal
SMPTE ST 425 compliant
<SDI IN 2> terminal
1 set (BNC)
SD-SDI signal SMPTE ST 259 compliant
HD-SDI signal SMPTE ST 292 compliant
3G-SDI signal SMPTE ST 424 compliant
Dual link HD-SDI
(LINK-B) signal
SMPTE ST 372 compliant
Dual link 3G-SDI (Link
2) signal
SMPTE ST 425 compliant
<MULTI PROJECTOR SYNC
IN> terminal/<3D SYNC 1 IN/
OUT> terminal (dual purpose)
1 set (BNC)
TTL high impedance
When [3D SYNC MODE] is set to output, TTL output: Maximum 10 mA
<MULTI PROJECTOR SYNC
OUT> terminal/<3D SYNC 2
OUT> terminal (dual purpose)
1 set (BNC)
TTL output: Maximum 10 mA
<SERIAL IN>/ <SERIAL OUT>
terminal
D-Sub 9 p, 1 set each, RS-232C compliant, for computer control
<REMOTE 1 IN>/ <REMOTE 1
OUT> terminal
M3 stereo mini jack, 1 set each, for remote control (wired)/for projector connection control
<REMOTE 2 IN> terminal 1 set, D-Sub 9 p, for contact control
<DIGITAL LINK/LAN> terminal
1 set, RJ-45, for network and DIGITAL LINK connections (HDBaseT
TM
compliant), PJLink compatible,
100Base-TX, Art-Net compatible, HDCP compatible, Deep Color compatible
<DC OUT 1> terminal/<DC
OUT 2> terminal
2 sets, USB connector (type A), for power supply only (DC 5 V, maximum 900 mA for each terminal)